Why the steel tube were strtched at the end of analysis ?

Dear all, Iam working in CFST column under cyclic loading in abaqus program, at the beginning of analysis all the mesh was fine, but at the end of the analysis there some deletion and stretching...

08 April 2019 4,840 2 View

How can one Determine the LTE Uplink resources of the access network and uplink resources in data transmission M2M communications?

The system is consisted of a single cell with one BS at the center with the following parameters :- * N=5000 (number of M2M nodes). * TRA=1000 sec. (the time interval between two consecutive...

13 August 2018 9,265 2 View

The coating process of ammonium nitrate at temperature 60 degree, what is the effect of phase transition on coating performance ?

phase transition of ammonium nitrate occur at temperature -18 to 50

02 March 2018 7,306 2 View

How to calculate The total delay of the packet for (CSMA) based system ?

How to calculate The total delay of the packet (i) for (CSMA) based system in M2M communication.?

01 February 2018 8,680 0 View

How can I determine the thickness of coating layer (surfactant material) on surface of ammonium nitrate by using SEM and TEM or by other instruments?

How can I determine the thickness of coating layer (surfactant material) on surface of ammonium nitrate by using SEM and TEM or by other instruments?

26 November 2016 3,824 13 View

What are good references for 'Introspective Design Research'?

31 March 2016 3,567 1 View

What is the fastest way to determine the PUSCH Resources after successful received RAR ?

for the LTE system with BW=1.4MHZ. PRCH_config index=0 (54 preambles in even frames). What is the fastest way to determine the PUSCH Resources after successful received RAR ?

01 January 1970 2,215 0 View

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10?

What's the best way to measure growth rates in House sparrow chicks from day 2 to day 10? Since, the growth curve from day 2 to 10 won't be like the "Logistic curve" it might not follow logistic...

03 March 2021 1,401 3 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before?

Question to you and THEM, the New Journal, "Integrative Psychological and Behavioral Science" -- do you not know, and have you not seen, this done before? There appears to be a core problem for...

02 March 2021 3,024 2 View

Which is a lucid standard comprehensive book to guide on psychological scale construction and its standardization?

02 March 2021 7,082 3 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Shall I skip the measurement model in SmartPLS?

Hello everyone, I had run a mediation model in SmartPLS using questionnaires that were already validated among my statistical population. A professor who edited my paper -though she is not...

01 March 2021 3,052 3 View

LOAD DISPLACEMENT CURVES Stiffness increasing in ANSYS non linear analysis. HOW CAN I CORRECT IT?

Hi. I am doing non linear FE analysis using a new material beam under flexural 2 point loading using ANSYS. I have defined a bilinear material model. The solution has converged. In results I am...

01 March 2021 9,911 3 View

What is involved in morphological changes of SEM images of a substance?

In the sem analysis of CaCO3 nanaoparticles, the morphology images showed spherical shaped particles but the proposed morphology for these type of nanoparticles is trigonal. I prepared the...

01 March 2021 1,960 4 View