Why I couldn't get the crystalline structure of LNO using soild state method even though the calcination temp is 1200 centigrade?

29 May 2023 1 7K Report

the crystalline structure of LNO using soild state method is not obtained even at 1200 centigrade...

calcinated for 3 hr at 1200

You say that you do not obtain LNO, but in your sample do you find traces of the reagents? Or other phases form? Are you sure that your experimental conditions are the right ones? Do you derive temperature and time from a published paper?

Badges
Science topic

Similar topics
Mathematics

More Tahir Ali's questions See All

Hello fellow researcher .. What is the meaning of your name?

I would like to create a small guide containing the meanings of the names .. Thanks to everyone who cooperates with me in achieving it.

03 March 2021 5,266 4 View

Can we classify HV and LV lines based on line length?

I have dataset which shows the length of power lines. I need to classify the lines based on the line length. Is there a rule to classify the High voltage (HV) and low voltage (LV) lines based on...

03 March 2021 4,116 4 View

How to figure out easily the right journal with the right scope for your paper?

According to my experience most of the selected journals during paper submission are based on journal text matching suggested results from Springer, Elsevier,,,Etc. then the manuscript happened to...

01 March 2021 1,786 3 View

How to model the battery pack in PSIM or PSCAD?

Hello, I have simulated a single battery cell using Thevenin equivalent circuit. For a battery pack, I have a large number of cells connected in series and parallel connections. Is there any way...

28 February 2021 2,116 1 View

Which is better medicine or food in obesity?

Preference in terms of the scientific aspect

28 February 2021 796 2 View

How could I take into consideration the weights of observation in a system of seemingly unrelated regressions (SUR) in rstudio?

I build a model of 4 regression equations (probit and OLS) in R studio. I need to take the weights of observations into consideration. While it is simple to do so for every regression equation,...

27 February 2021 1,233 1 View

Can anyone share his experience regards Smoothing in origin?

I am working on TiO2 composite material and the results of XRD have a lot of small/junk peaks and while I apply a smooth filter in Origin then the other characteristics peaks disappear so anyone...

26 February 2021 8,183 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

Is there any software or formula for sample size determination by using sensitivity and specificity?

I want to conduct research on the diagnostic performance of some tests. I want to calculate sample size by using the sensitivity and specificity of the test in the previous studies. So Is there...

23 February 2021 619 5 View

How to find natural frequency of a bridge from vehicle induced vibrations?

i have frequencies of bridge that are effected by mass of vehicle. the problem is when any vehicle pass the bridge it would add the its mass to the bridge mass ultimately mass of the bridge will...

22 February 2021 10,004 3 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

What to do with absence of fluorescence label in Fucci2a mouse-derived fibroblast culture?

Dear all, I have harvested fibroblast cells from R26p-Fucci2 mouse embryos (mouse line as described in this paper: https://dev.biologists.org/content/140/1/237) and cultured them on plastic,...

17 February 2021 3,368 2 View

How to raise temperature in small increments during equilibration in LAMMPS?

All, I am trying to equilibrate an Ice 1h crystalline structure to 250K in LAMMPS. When I tried to do this at 250K directly, the structure lost it's crystalline shape and became disordered post...

14 February 2021 5,747 2 View

How to make Fast Green FCF from powder?

Hi everyone We need Fast Green to electroporate plasmid into mice embryos, therefore we simply need it to see some color in the liquid we are electroporating so that electroporation is more...

07 February 2021 1,671 2 View

Which software is the best to model a non-linear concrete (ABAQUS, ANSYS,ADINA, ATENA, etc.)?

What is the best finite element modeling software packages for modeling non-linear and fracture analysis of CONCRETE? I've had some with ABAQUS standart/explicit, but I would like to learn if...

27 January 2021 330 6 View

What stress-strain graphs do I put in a smeared concrete and steel reinforcement element in finite element analysis?

My SOLID65 element is reinforced concrete but what modulus of elasticity and material properties do I put? For nonlinear analysis

26 January 2021 1,704 3 View

Should the Ice 1h crystalline structure be lost during equilibration process in LAMMPS?

I have created an Ice 1h structure and am equilibrating it 100K in NVT ensemble in LAMMPS for a timestep of 0.25fs in 3000 steps. The potential used is TIP4P/Ice. Although the simulation runs fine...

26 January 2021 9,603 11 View

Do Fire damages Concrete Structures Below soil?

Hi All, I am working on the rehabilitation of a fire-damaged structure. Should I consider the Column below Soil structurally deficient. visually it doesn't look like fire affected the column...

12 January 2021 5,401 3 View