Stable beta titanium alloys do not change their phase composition during heat treatment. But my experiments have shown that heat treatment (homogenizing annealing and quenching) alters Young's modulus. Any idea what might bedoing that?
thanks for all
02 December 2023 6,239 3 View
I am looking for LC-MS spectrum of the common adder Vipera berus with or without identification of individual peaks to compare with my results.
17 August 2023 5,877 1 View
Looking for objective performance criteria ISMS
30 January 2022 4,491 4 View
Dear all Could you, please, advice on the origin of these particulate contamination that appears to happen solely in the matter-containing region of the epoxy slice? I'm investigating insect...
12 September 2021 7,520 3 View
I want to generate electron density map after Rietveld refinement in GSAS II software.
10 August 2021 1,723 3 View
I've run into really strong discrepancy between individual genes topologies. Reasons for it quite well known, but what about solutions?
23 June 2021 4,042 0 View
What is so special about metallic Pd that it can absorb around 900 times its own volumes of hydrogen? I was searching articles, but I couldn't find an answer to this question. All researchers say...
22 June 2021 3,520 5 View
Dear community, I performed XRR measurements on thin film AuAgSi alloys deposited on Si substrate, please see attached image. For simulation i included 2 nm of SiO2 on top of the substrate and i...
03 February 2021 5,611 2 View
Hello, I am looking for a GIS tool (ArcGIS, QGIS, R, etc.) that will calculate a measure of habitat connectivity for nodes along an aquatic (estuarine) network? My dataset is comprised of a...
12 January 2021 6,413 2 View
Dear community, do you know whether the vacuum flanges widely used in Zeiss SEMs and FIBs correspond to some standard or not? The picture is attached, the outer diameter is 83 mm.
06 July 2020 8,715 0 View
I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...
07 August 2024 1,028 0 View
Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...
07 August 2024 9,563 0 View
Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...
06 August 2024 1,989 3 View
is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it
06 August 2024 947 1 View
I am interested to know the behavior of dyes toward light. Specifically, Blue dyes re-emit the spectrum, especially from the green zone (known as principal in LED lamps, and blue dyes are known...
05 August 2024 3,290 1 View
I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?
04 August 2024 1,537 1 View
I fabricated Ti3C2Tx using concentrated HF 40%, I plot an XRD as attached image below.. please let to know if I obtained it or not.
02 August 2024 6,789 4 View
How select composition for ods-high entropy alloys?
31 July 2024 2,795 1 View
Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...
30 July 2024 3,849 0 View
A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids
28 July 2024 4,985 1 View