Cross section of Uranium-238 at different fast energies of neutron?

Dear All, The neutron cross section of element generally falls with the increase in neutron energy. But in U-238 the fission cross section at Neutron energy of 1MeV is 0.3 barns whereas it...

02 March 2017 1,600 4 View

Ideality factor for diodes?

Is there any mathematical formula there for the ideality factor of the diodes? I will be very much thankful for the above. Please send the mathematical expression for it.

08 September 2016 6,873 5 View

The pulse shaping circuit of the radiation detector?

In the radiation detector the pulse shaping circuit consists of CR-RC circuit and amplifier.The function of pulse shaping amplifier is to improve Signal to Noise ratio.It also act as a filter to...

08 September 2016 8,346 4 View

How to reduce shot noise in the semiconductor radiation detector?

Generally there are three types of noise is present in the semiconductor radiation detector.These are Thermal Noise,Shot noise and Flicker Noise.The thermal noise is removed by operating the...

08 September 2016 9,187 2 View

Coating of Enriched Boon-10 on Si Surface other than CVD technique?

Dear All, Is there any technique other than the CVD to coat the Enriched Boron-10 on the Si surface? I will be very much thankful for the reply. Thanks & Regards Manoj

08 September 2016 8,542 0 View

In radiation detector Generally the HV Bias to the detector is given through the charge sensitive Preamplifier?

08 September 2016 4,031 4 View

Neutron irradiation effect on semiconductor PIN Diode?

I have performed the neutron irradiation on the PIN Diode. I have found that the forward bias cut-in volatge has been shifted. Why these shift been observed in the neutron irradiated PIN...

06 July 2016 7,854 3 View

Why electric field is maximum at the center of the depletion region in the PN junction?

In the depletion region only uncovered ions are exiting then why we have the maximum electric field at the center of the junction?

06 July 2016 7,199 6 View

How does a guard ring in the PIN Diodes reduces the surface leakage current?

06 July 2016 6,512 2 View

Common mode signal calaculation?

Dear All, For the common mode signal the input voltage is calculated as (V1+V2)/2. Why we are calculating the common mode input signal as (V1+V2)/2 whereas in differential mode the input signal is...

04 May 2016 1,958 1 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Physics: Why do we describe light by referring to its wavelength, but microwaves and radar pulses by referring to their frequency?

In physics, the description of the properties of light generally refers to its wavelength (nm), while in the range of microwaves and radio waves we refer to the frequency of a signal (e.g. kHz or...

03 March 2021 1,682 3 View

What is the production process of CaFe ferroalloys?

I looking for ferro calcium production process

03 March 2021 1,755 4 View

12% ledeburitic cold work tool steel, etched for revealing retained austenite, any help for clarifying?

Hello everyone. Given microstructure image belongs to a 12% ledeburitic cold work tool steel (annealed and tempered). The sample was etched with picral (100 mL ethanol and 4 g picric acid). I...

02 March 2021 4,119 3 View

Is there any effect of different colours of light (white, red, yellow, blue etc.) on the rate of photosynthesis? If yes, why?

Light is inevitable for the process of photosynthesis reaction. Naturally sunlight plays the vital role for this process. Light may be of different colours like white, red, yellow, blue etc....

02 March 2021 7,890 2 View

How to calculate average trend in maximum annual NDVI from MODIS?

I am wanting to calculate the average trend in maximum annual NDVI in Iceland from 2010-2020 using MODIS MYD13Q1 V6. How would I do this? I have currently inserted the NDVI bands from the MODIS...

02 March 2021 752 2 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View

How can you bring two structures together to create an adhesive bond in LAMMPS?

I have created an Ice 1h crystalline structure and an Aluminium substrate structure and equilibrated both at 250K. Now I need to bring them together in a way that an adhesive bond is created....

01 March 2021 3,325 2 View

Can polymer concentrations be calculated based on the number average molecular weight?

Hello, I spin-cast two different polymers onto wafers and measure their height as a function of initial concentration. For polymer A, I have the weight-average molecular weight (Mw) as well as...

28 February 2021 7,882 2 View