Why does Fluka simulations shows finished ok without simulating?

15 January 2025 0 2K Report

I am struggling with Fluka simulations as my input file is correct but still no running simulation can be observed. Although I run simulations successfully once before but cannot figure out the issue now. If any one knows fluka simulations please help me out.

Badges
Science topic

More Hafiz Ghullam Rasool's questions See All

Absorption coefficient of methane?

Hello, Can anyone provide me with the absorption coefficient of methane gas at 7.7 um? Any reference?

06 August 2024 980 5 View

How are Large Models Exploring and Outputting Knowledge Understanding in Specific Content Areas, and What Does Academic Research Say About It?

Hello everyone！ I am currently exploring the performance of large models in understanding knowledge in specific domains, and attempting to construct a knowledge framework similar to what...

05 August 2024 5,729 2 View

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity?

Regarding a model for simulating battery charge and discharge, what do you consider to be high fidelity? What is the acceptable percentage of error (regardless of the metric)? Could you suggest...

03 August 2024 5,358 0 View

How do i get an account to upload my published papers?

need to open an account to upload my published papers

01 August 2024 9,255 1 View

What is the problem with these tissue culture plants?

All plants are green but some of these plants becomes yellow. I did not found any reason. Please help me to find out the real problem.

01 August 2024 589 4 View

How to correctly use the UTE and ZTE pulse sequences in Bruker's ParaVision software?

I am using a Bruker 600M solid-state NMR spectrometer with a Micro 2.5 microimaging system. The test sample is a tube of 1M LiCl aqueous solution, and the nucleus detected is 1H. I am trying to...

01 August 2024 9,227 1 View

Is artifacts in XPS possible to build high deviation in binding energy larger than 5 eV??

Hello. Thanks for your consideration to see my question. Recently, I conducted XPS anaylsis of g-CN that is prepared from thermal polycondensation of DCDA, so-called conventional bulk-g-CN,...

30 July 2024 9,824 2 View

Which statistical test should we use?

N=6 Comparing pre and post test likert scale responses. Participants are mix of practicing & preservice teachers.

30 July 2024 7,233 4 View

How to build my own lab made four point probe set up?

Hello, I'm trying to measure the conductivity of semiconductor films but since I don't have a commercial four point probe set up I would like to build one on my own in my lab. I have generators,...

30 July 2024 906 2 View

Can the limit of quantification (LOQ) of an analytical method fall outside its linear dynamic range, or must it always be within it?

Can an analytical method's limit of quantification (LOQ) be outside its linear dynamic range, or is it always required to be within it? Please provide a thorough explanation supported by verified...

29 July 2024 7,198 9 View

Are radiation shielding glasses too important to carry out numerous simulation studies?

Very many published papers exist on radiation shielding glasses, all with identical simulation techniques, performed with the MCNPX, FLUKA and GEANT4. I don't really realize if such extensive...

01 November 2023 4,426 6 View

Dosimetry simulation program : geant4 vs fluka vs egs vs mcnp ?

dosimetry simulation

11 February 2023 1,964 3 View

FLUKA:How to quickly get started with fluka?

Currently I have installed fluka and flair. what information is available for me to quickly get started with fluka, and implement some energy spectrum calculations?

05 December 2022 9,581 1 View

Could you provide me iron(ii) chloride fluka company just image in need it?

in fact, I searched about iron(ii) chloride fluka or BHD company image. you can help, I need it in my presentation next week please, help and cooperation with me. the student alaa. many thanks

25 September 2021 1,982 2 View

Dicom images into fluka ?

Hello, I'm looking for uploading dicom images to use it in Fluka Mc code. Could everyone help me ? Thanks in advance.

01 January 2021 6,753 2 View

Dear All, I want to calculate the proton primary dose and yield in water for 250 Mev proton beam using Fluka Code but I couldn't. What should I do ?

Dear All, I want to calculate the proton primary dose and yield in water for 250 Mev proton beam using Fluka Mc Code but I couldn't. I think it's because detector data entered incorrectly. So what...

19 February 2020 6,820 5 View

How can I remove sulfur from ICP-MS cones?

I have been analyzing a set of samples that are high in sulfate for the last few months. I have noticed that after a while a powdery yellow substance builds up on my skimmer cone resulting in more...

02 April 2019 6,477 4 View

Can anybody from the mass spec community recommend a vendor for alpha-cyano-hydroxycinnamic acid butylamine (CHCAB)?

We have used this ionic liquid matrix for MALDI mass spectrometric analysis of highly sulfated saccharides, but this product is not anymore available at Sigma/Fluka and we failed to find another...

06 July 2018 2,012 5 View

Experience on parallelization of virtualbox? Especially for running MC codes (eg GATE , FLUKA) which r LINUX-based but they need VB to be run on Win?

How to speed up the running of Monte Carlo codes when using virtual LINUX on WINDOWS.

04 May 2018 3,417 0 View

What is the basis of modelation a Hadron-nucleon inelastic collisions in FLUKA ?

FLUKA

03 April 2017 9,120 0 View