How to calculate the crystallinity of cellulose film?

27 February 2021 2,753 4 View

How does GROMACS calculate the average structure of proteins?

I want to get a average structure from a pdb file containing multiple models. I used the command below: gmx cluster -f input.pdb -s topol.tpr -cutoff 20 -method gromos -av GROMACS...

25 February 2021 6,314 1 View

No title

The regenerated cellulose film was prepared by zinc chloride/H2O system. The zinc chloride had been washed away in the regeneration process, and the wet film which was not dried had uniform...

18 February 2021 9,538 1 View

R/Python package for time-intensity or progressive profiling in sensory evaluation?

Hi I've been looking for a stat package for my sensory evaluation data (progressive profiled which is a multi-timepoint version of descriptive analysis). Is there any available one to...

08 February 2021 9,170 3 View

How can I make sure the simulation results of the water droplet impacting on the wall using the FLUENT agree with the experimental results?

Dear researchers, I am modeling the process of the water droplet impacting on the wall with a constant contact angle. The specific calculation parameters are as follows: The droplet diameter is...

24 January 2021 1,020 5 View

Mysterious line across SDS gel?

Does anyone have the similar issue? A line across the denature SDS gel shows up after staining with Coomassie blue and there are many lines in every lane if you take a closer look. This gel had 15...

07 January 2021 5,610 4 View

How can I calculate packing density of particles by fomulas or softwares?

I have all data of particles, such as size distribution, or numbers. Is there any way that I can calculate the packing density of these particles? Assume that all particles are circular.

05 January 2021 4,272 2 View

After cellulose is regenerated in water, a cellulose hydrogel is formed. I want to know if there is crystallinity inside the the hydrogel?

After cellulose is dissolved and regenerated in water, a regenerated cellulose hydrogel is formed. I want to know if there is crystallinity inside the hydrogel, or it will not crystallize until it...

04 January 2021 7,466 4 View

How can I fix the density of system in coarsed grain simulation?

In the process of obtaining the nonbond potential of the Coarse-grained(CG) model, I need to simulate the CG model mapped from the conformation of all atom(AA). AA simulation process is...

02 January 2021 3,643 1 View

How to export Mass and Stiffness matrices using Ansys Workbench?

Hello, I am trying to export Mass and Stiffness matrices using Ansys Workbench via Modal analysis modular, with APDL commands inserted. However, there is no .matrix file generated. Could anyone...

17 December 2020 1,196 5 View

How to define and get results (stresses) for certain points of a model in abaqus, using python? When the size of the model changes?

I want to do a parameter study of a aixsymmetric cylinder in Abaqus. I want to create several jobs where I get the stresses for 3 different points in my model. These points are defined. I wrote a...

01 March 2021 10,078 1 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS?

I need to model masonry and reinforced concrete minarets for my MSc thesis. Which one is easier and better at modeling slender masonry structures? ANSYS or ABAQUS? (Or any other program for just...

01 March 2021 736 3 View

How to assign different material properties to each element in Abaqus ?

Hello, I am writing a python script to generate my model and write the input file. The problem is I have 1000 elements in my mesh and I want to assign different material properties to each...

01 March 2021 9,511 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

How to find the right number of integration points in second order 3d finite elements?

I am familiar with finite element simulations and numerical schemes like the Gauss Legendre quadrature. I also know that the Gauss integration yields exact values for polynomials up to degree 2n-1...

27 February 2021 6,818 3 View

How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials?

Hi, all! How can we use a hybrid element in Abaqus Dynamic/Explicit for impressible materials? I have not find the choice for explicit element in Abaqus CAE. I am wondering whether it is possible...

25 February 2021 9,936 2 View

Is it possible to do optimization for a submodel in Abaqus?

I'm trying to run an optimization in Abaqus for a submodel with no luck, jobs are not being create for submission. Is this even possible? or is Abaqus limited to do Opt. for the model itself...

24 February 2021 4,908 5 View