Why a negative pressure is formed behind the projected flat plate? what is its physical significance?

12 December 2016 0 2K Report

why a negative pressure is formed behind the projected flat plate? what is its physical significance?

Badges
Science topic

Similar topics
Physics

More Shailesh KUMAR Jha's questions See All

Why angle of attack has no effect on acoustics characteristics of an airfoil?

I just want know why AOA (angle of attack) has no role on acoustic features of an airfoil/ flat plate. If we go for aerodynamics AOA plays a vital role but this is absent in acoustics case why is...

04 May 2019 3,579 12 View

Vibration control of a blower installed at the top of the building on a cast iron frame?

I want to developed an aeroacoustics lab at the second floor of the building but the blower and the 20 HP motor is causing too much noise which dominate over the airfoil noise so we like to...

11 December 2018 1,685 3 View

Is it possible to do aero acoustics analysis using Ansys Fluent?

How to do Aero acoustics analysis of the 2 D flow problem in Ansys fluent with k-epsilon model? What commands has to be given for this analysis in this commercial software?

05 June 2018 3,578 6 View

What Boundary condition should we give at the domain in order to capture the Tip vortex effect?

Can Any body help in getting the boundary condition at the domain to get the tip vortex effect in our 3-d simulation using ANsys fluent commercial software?

04 May 2018 7,815 4 View

PSD plot of velocity v/s time?

what does PSD plot revels for flow over airfoil and plate? What physical interpretation we get from PSD plot for aerodynamics point of view? why we are plotting PSD v/s Frequency? Please Give some...

01 February 2018 9,879 4 View

How to calculate a wake length behind a streamline body?

I want to know how we can calculate the wake length behind the stream line body in its post stall region with the help of Ansys fluent simulation. How to do averaging of the flow (is there any...

31 December 2017 6,034 5 View

How to perform POD and DMD of transient problem?

I am working on Ansys fluent and I want to know how i can perform POD and DMD of my current flow problem over inclined flat plate at high angle of attack(in ansys fluent) in post processing state...

31 December 2017 5,191 3 View

How to calculate vortex energy by the help of Power spectrum density plot?

11 December 2016 8,964 0 View

How to find the accuracy of load cells which can measure lift and drag forces?

How to find the accuracy of load cells which can measure lift and drag forces? Plz provide me some good supplier of load cells in INDIA?

06 July 2016 1,537 0 View

How to develop investments in renewable energy sources?

08 August 2024 5,112 3 View

1. If I can quantize the atom using this hyperbolic spiral and classical physics, could nature do the same?

If we map as a continuous motion an ionising electron (beginning its journey at n=1) in an H atom, a specific hyperbolic spiral appears (see animation). When we solve this spiral formula, we find...

07 August 2024 5,343 2 View

How are iso-frequency contours plotted?

Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...

07 August 2024 1,937 1 View

Is changing the medium during the experiment overestimate the results?

I am experimenting with cancer and non-cancer cells in a 12-well plate for 4 days with a seeding density 1*10^4/well, however, I noticed that the control group growth rate slows down on D3. Should...

07 August 2024 2,283 2 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

How to normalize and take the significance of the MTT OD values with 3 replicates for the same cell-line?

Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...

07 August 2024 8,106 4 View

How to assess the osmotic power of a substance?

Hello, I suspect that a molecule I am using is causing bacteria to experience osmotic shock. What chemical properties should I look for to compare this capability with those of other substances?...

06 August 2024 977 1 View

Can you recommend a 96-well plate for minimal cell adherence to the wells during phagocytosis experiments?

I have been performing short phagocytosis experiments using 96-round bottom, tissue culture treated, well plates (Falcon, 353077). I culture the cells with the phagocytic cargo for 2-4hrs, wash...

04 August 2024 5,228 4 View

PBMC infection with virus?

In my study, I intend to infect PBMCs with SARS-CoV-2. After that, I will analyze NK cells by flow cytometry to see if their phenotype changes or if they show degranulation. After the infection, I...

01 August 2024 4,403 4 View

Found this object in the cell culture - do you have any suggestions what it might be?

Dear researchers, Today, we found this object in one of the wells of a 96wp culture plate. The plate contained MEC-1 cells and GelTrex. I am quite curious what this is (because it's not cells). Do...

01 August 2024 2,250 2 View