Which third party CFD Codes can be used for FSI Co-Simulation in Abaqus ?

More Rahul Kaushik's questions See All

Does anyone use antinuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples?

I am looking for anti-nuclear antibody (ANA) and anti-Phospholipid antibody ELISA kit for Non Human Primate serum samples. Any suggestions highly appreciated. Thank you.

28 February 2021 6,512 3 View

Treating Intermediate Variable in Linear Regression Analysis in SPSS?

While performing the Linear regression analysis in SPSS version 26.0.0. my intermediate/mediation variable goes to the excluded section. Please share your valuable suggestion "How to restrain the...

25 February 2021 4,591 5 View

Which DL architecture is better to work on handwritten data?

I am working in the area of Handwriting recognition for Bangla. As there are many DL architecture, I am confused which one to select.

15 February 2021 4,996 1 View

How is Initial GDP measured ?

Dear All, I am working on estimating Debt-Growth Threshold but confused about some points. My questions are; - How do we calculate initial GDP Per Capita? Shall we do it in STATA or excel file?...

15 February 2021 2,677 2 View

Having trouble with qPCR amplification plots. My curve's never seem to reach a plateau. Any ideas?

The parameters of the curve all seem acceptable, typically reactions results are above 0.9852, -3.1 to -3.6 slope, and 90-110% reaction efficiency. The results seem to be what I would expect from...

04 February 2021 1,138 3 View

How can I get rid of the bubbles in the SBS membrane?

I used methylcyclohexane/ ethylcyclohexane / n-butyl acetate mixed solvent to dissolve thermoplastic SBS & terpene resin. The mixture is then poured onto a glass substrate. After solvent...

24 January 2021 8,306 3 View

Can anyone provide me a protocl of Native PAGE with the 30% terminal resolving gel concentraion?

I am separating the AuCNs, which are Au nanoclusters. I used the 3% stacking and 30% resolving polyacrylamide from the reference. Eachtime when the resolving gel is polymerizing, plenty of heat...

22 January 2021 8,522 3 View

After G actin polymerization and labelling I didn't got filaments. Why?

Purified G actin and got 42kda band and an additional band just below it. While performing G actin polymerization and labeling with rhodamine-phalloidin I didn't observe filaments under the...

20 January 2021 3,751 2 View

How to interpret multiple bell shaped curves in Kratky plot?

Hi, I'm trying to analyze a Kratky plot generated from my SAXS data. I am seeing multiple bell-shaped curves in my Kratky plot and I am not able to find any source to get relevant info on this...

20 January 2021 2,474 1 View

Lift off problem with Indium/Gold deposition?

Hi, I'm doing 5/40nm In/Au e-beam evaporation at rates 0.2A/s(for In),1A/s(Au) on lithographically(doubly coated 495k,950k PMMA e-beam resist) done Si substrate at base pressure 2e-6torr. I'm...

18 January 2021 7,550 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Thomas Frank

...or doing the entire FSI-CoSimulation in ANSYS Mechanical plus CFX or Fluent?

Usually it is a much more "strenuous" approach to attempt to couple successfully the codes of two different software vendors (e.g. issues with different life cycles of different releases; explicit and segregated coupling of two different tools, etc.).

Regards,

Dr. Th. Frank.

Ahmed Ramadhan Al-Obaidi

I agree with Thomas

Mikko Brummer

Dassault Systemes XFlow is easily coupled with Abaqus. See for instance https://www.youtube.com/watch?v=-V4Nlp9pSMc

or here https://www.4realsim.com/xflow-cfd-2017x-new-release/

XFlow is a relatively new, Lattice-Bolzmann based super advanced but easy to use CFD code.