Which TCAD tool can I use to study low frequency noise in MOSFETs?

More Arjun Ajaykumar's questions See All

Can the switch-OFF transients in Semiconductor-On-Insulator devices depend on the intrinsic mobility of the material?

Switch-on and switch-off current transients in silicon-on-insulator devices is well known. For a conceptual semiconductor-or-insulator device, do we expect to see any dependence of the switch-on...

01 February 2018 2,764 0 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

What do I do with DLS peaks that are from the buffer?

I'm looking at the aggregation of my protein sample using DLS. Unfortunately, my buffer (20mM HEPES) also results in a set of peaks. These are at approximately 1 and 1000 d.nm. The lowest peak...

01 March 2021 9,015 2 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

What low-cut filter (high Pass frequency) to be used for response spectrum (Tripartite plots) ?

What low-cut filter (high Pass frequency) to be used for the response spectrum (Tripartite plots)? I am currently working on differentiating between hard/soft site responses in Indo-Gangetic...

21 February 2021 9,273 2 View

How can I plot surface potential vs Gate voltage in Sentaurus TCAD?

Currently, I am working on a project in Sentaurus TCAD for which I required the plot of Surface Potential Vs Gate Voltage. Can anyone help me finding the simplest way or a different procedure for...

18 February 2021 1,213 2 View

QPCR tubes for Roche Lightcycler Nano?

We own a small cPCR thermal cycler from Roche, Lightcycler Nano, which is convenient for backup quick runs. Recently, Roche has discontinued the plastics for it and they offer no alternative from...

17 February 2021 8,694 5 View

Best synthesis method for large scale silver nanoparticle synthesis with high yield?.Best post processing steps after nanoparticle synthesis?

I have chemically synthesized silver nanoparticle to combat microbes on wound site. I have used many methods of synthesis, but I found minimal field of silver NP product.I am getting whitish...

11 February 2021 4,964 13 View

Deepak Kumar Sharma

Hey all,

I am using sdevice for low frequency noice,

But i have question that why they are doing frequency sweep in example given in sdevice manual.

I was expecting that we juct have to give consatant dc voltage at gate and drain and analyse the nodes.

Can someone help me in that?