What is the best metod for preparation of thin films of chalcogenide glasses?

Give suitable answer for the same.

01 February 2018 920 3 View

Is chalcogenide materials suitable for proto type three dimensional printing?

give suitable answer.

31 December 2016 6,723 0 View

What is the difference between four probe and two probe measurement method?

Well known answer is that, two probe method is appropiate only for highly resistive material and four probe measurement method is only for low resistive material, but for determination of band gap...

08 September 2016 8,364 9 View

Is it possible to draw a B-H curve for chalcogenide glasses?

Explain and give suitable references.

08 September 2016 4,085 2 View

What are important factors, those can be evaluated by dielectrical measurements?

07 August 2016 1,302 3 View

It have been observed that density of defects states of thin films of chalcogenide glasses are more than bulk samples, why?

Explain with suitable references.

07 August 2016 6,757 2 View

What may be the grain size of nanocrystalline materials?

Explain and give correct explanation.

03 April 2016 6,686 4 View

What are the important factors that can be evaluated by dielectric measurements of nanocrystalline materials?

Explain and give the suitable formulae.

02 March 2016 8,761 4 View

How can we connect the study of light induced defects in chalcogenide glasses for solar cell applications?

02 March 2016 4,490 4 View

Is it possible to prepare nano thin film from nanopowder?

10 November 2015 1,667 7 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

How to Eliminate cosine error and abbe error in LASER measurement system(for example Rhenishaw XL80)?

I like to do project in laser measurement system. My objective is to eliminate or reduce the cosine error, abbe error in Laser measurement system. I have Rhenishaw XL80 system. Please tell the...

28 February 2021 4,890 3 View

How can we limit artifacts caused by rotation in fiber photometry?

We are trying to run fiber photometry experiments for long time scales, but we get these sinusoidal artifacts that come up. We think they may be caused by twisting of the fiber optic subject...

25 February 2021 568 1 View

How to measure angle between laser travel path and machine axis in Laser Measurement system?

25 February 2021 1,987 3 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

Which thermal conductivity test recommended for Ag-Cu nanofluid?

I have prepared Ag-Cu alloy with polymer coating upon it.... how can I measure thermal conductivity of it ?

22 February 2021 5,915 3 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

How can I simulate the optical absorption spectrum of a biomaterial (like DNA or protein) in COMSOL?

I need to simulate the optical properties of a biomaterial, namely DNA, in COMSOL. Basically I need to simulate the IR absorption spectrum of a cylinder filled with a 'concentration' of DNA. I am...

21 February 2021 3,043 3 View

What are damage parameters for SMA while modelling on ABAQUS 2020?

I have given Elastic and Superelastic material properties, but I think we need to provide the damage parameters also. Please help me here.

16 February 2021 8,694 1 View