Which is easier to electrospin? Conductive polyaniline or polypyrrole?

Which is easier to electrospin? Conductive polyaniline or polypyrrole?

09 October 2015 4,352 3 View

How do I aminate GO (graphene oxide)?

09 October 2015 517 2 View

Any update about closing the intrinsic defects within graphene?

Any update about closing the intrinsic defects within graphene?

09 October 2015 8,413 0 View

Do you know what are the advances in production of graphene using CVD process?

Do you know what are the advances in production of graphene using CVD process?

09 October 2015 1,565 0 View

What are the factors that control the absorption capacity of water super-absorption polymer salts? like Sodium polyacrylate?

What are the factors that controlling the absorption capacity of water super-absorption polymer salts? like Sodium polyacrylate?

09 October 2015 1,842 2 View

Which is the most efficient etching solution for nickel based alloys?

Which solution reveals the microstructure and features of nickel-based alloys?

02 March 2021 2,221 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

Which transition metal salt precursor is best for doping? Why?

I would like to synthesize a transition metal doped TiO2 via solgel method. Hence, I would like to know which metal salt precursor to choose among Chloride, Nitrate, and Sulphate. A clear...

27 February 2021 4,285 3 View

How can I selectively dry etch Ti on a polymer substrate?

24 February 2021 5,378 1 View

Thermal reduction of graphene oxide.?

I am trying to reduce graphene oxide by thermally but I have no proper information regarding this. Can any one help me regarding the details about temperature and time for the reduction of...

23 February 2021 4,155 4 View

Is there an ideal incubation time of RGO-modified SPCE before subsequent use, i.e., electrochemical characterization or further modification?

I notice that upon washing and air-drying of my RGO/SPCE surface and characterizing again via DPV, the current response towards ferricyanide probe significantly decreases. My worry is that the...

22 February 2021 5,324 3 View

What is the best etching method for Mg-Ca alloy?

I have used Picral etchant (4.2 g Picric acid, 10 mL Acetic acid, 70 mL Ethanol, 10 mL distilled water) but it didn't work. Is there any alternative?

21 February 2021 2,558 5 View

What reaction will occur when adding hexamine into ammonium nitrate in an acidic medium?

Hello, I am investigating properties of water in oil emulsion explosives. And adding hexamine (hexamethylenetetramine) into one of the phases that are used to make the emulsion should increase the...

21 February 2021 8,680 1 View

When I reacted Bidentate NS Schiff Base with metal salt (M-Cl2) in +2 oxidation state in proportion of (2:1) , getting sticky product ,, why?

When I reacted Bidentate NS Schiff Base with metal salt (M-Cl2) metal chlorides in +2 oxidation state in proportion of (2:1 Schiff base &metal salt) , i was get sticky material Why ? ---~...

21 February 2021 7,970 5 View

What is the best substrate for exfoliating few layers of hexagonal boron nitride (hBN) using traditional scotch tape method?

Unlike graphene, it is usually very difficult to exfoliate few layers (~10 nm thick) of hBN on SiO2 substrate due to lip-lip interaction at the edges. Au substrates have been proven very useful...

16 February 2021 2,635 2 View