How can I convert netcdf file to a binary file in matlab?

Dear all, I have monthly nutrients data from WOA (in a separate NetCDF file) extracted for a specific region. I would like to convert these data directly into a bin file (one of the separate...

30 January 2021 9,241 2 View

How to design reverse primer with ambiguous nucleotides?

How to design, reverse primer with ambiguous nucleotides?

03 January 2021 6,762 4 View

Why does the DNA's elution decrease after centrifuging with spin column?

02 January 2021 987 4 View

How to synthesize pyrrolium ionic salt?

I am keenly interested in the synthesis of heteroaromatic ionic salts for use as an organic template. I want to synthesize alkyl pyrrolium chloride or bromide through a simple addition reaction...

30 December 2020 2,778 3 View

How can large volume ( 100 liters or more ) of carbon dots solution be purified and sieved cost-effectively?

Articles describing the use of carbon dots in agriculture have been increasing recently. Again, studies have found that carbon dots size and shape and some other features are effective. Therefore,...

30 December 2020 1,139 3 View

How to Modeling and simulation for launch vehicle?

Modeling and simulation for launch vehicle Title of graduation project for a master's thesis in mechanical engineering, specializing in Control Search assistance required? Thank you

28 December 2020 9,000 1 View

How to calculate average habitat suitability change between 2 different SDM/ENM?

Hi guys, I would love to know how I could go about solving the above question. I currently have 2 different species distribution models, one created with the current climate projection and the...

14 December 2020 864 8 View

What are good M.Sc thesis topic suggestions in construction management (specially BIM & Waste management area)?

My prefered area is in Waste management & BIM , where I have read about using 4D BIM & 5D in waste management , but I have not reached a significant research gap to work on it, so is...

03 December 2020 1,294 2 View

Why thrust force, temperature and surface roughness increase with feed rate in Machining?

Reasons why thrust force, temperature and surface roughness increase with feed rate in Machining?

17 November 2020 873 4 View

RBC's contamination during DNA extraction ?

Hi there! currently i am working with spin column kit for DNA extraction I've put almost 600 uL of buffy coat. after a lot of washing, the RBC's remained stucking in filter? How could i get rid...

25 October 2020 8,712 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View