Which electrolyte is generally used for electropolishing of Al and Mg (Al7075 and AZ31) alloy?

More Somayeh Kord's questions See All

Self healing metals?

What's the best paper about self healing metals?

03 April 2017 4,880 2 View

Can someone suggest what "Molecular Dynamic simulation" is and how to study it?

03 April 2017 5,630 1 View

How can I determine amorphous to crystalline ratio in an XRD pattern?

03 April 2017 3,863 3 View

Has an evaluation of the health risk of nanomaterials used in consumer products been undertaken?

01 January 1970 6,221 1 View

What are the mechanism of distribution nanoparticles by using ultrasonic waves in the manufacture of cast aluminum nanocomposites?

01 January 1970 5,315 12 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

How select composition for ods-high entropy alloys?

31 July 2024 2,795 1 View

I am trying to obtain microstructure for Mg-Zn-Sn alloy?

Any suggestions with respect to etchant composition and holding time?

27 July 2024 6,925 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

How to select temperatures for two-step aging treatment in high entropy superalloys?

Waspaloy is considered the benchmark alloy. Due to the different gamma prime solvus temperatures, we couldn't adopt the same double aging treatment. Can anyone suggest how to select temperatures...

13 July 2024 2,417 1 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

How to solve the problem that the film obtained by magnetron sputtering on the ternary alloy target A2BC is ABC (not A2BC)?

Using magnetron sputtering with an alloy target composed of A:B:C in a 2:1:1 ratio, the resulting thin film composition is A:B:C=1:1:1. How can you achieve a A:B:C=2:1:1 composition? What are some...

24 June 2024 1,605 0 View

Is there any suggestion on the explanation and reduction of stacking fault defects in high Al content InAlGaAs alloy lattice matched to InP?

24 June 2024 6,645 1 View

Can someone introduce an article about the convergence of the temperature parameter for the SPH part in Abaqus software?

For the article, I need some references for the subject of checking the convergence of the temperature field parameter for the SPH part in Abacus, and I want to study this case with a few meshes...

13 June 2024 2,504 0 View

Robert Král

Hello,

for AZ31 we have used Struers-AC2 electrolyte at -15 °C. See this link

https://www.researchgate.net/publication/225618197_Texture_and_microstructure_evolution_in_ultrafine-grained_AZ31_processed_by_EX-ECAP

Regards,

Robert

Article Texture and microstructure evolution in ultrafine-grained AZ...

Somayeh Kord

Thanks Robert

Thanks Ross. It is very good information.