How to use protein A G beads to purify antibody?

Secretory universal influenza antibody CR9114 were successfully expressed by adenovirus vector ,then we used protein A G beads purify CR9114.But the molecular weight of the purified antibody under...

22 February 2021 4,318 2 View

Amorphous silica XRD peak at around 10 degree?

21 February 2021 3,417 5 View

How could I get the P-value from the mean, SEM, and n of different groups in the t-test?

How could I get the P-value from the mean, SEM, and n of different groups in the t-test without the original data? For detail, I would like to know the P-value between BMP-2: 50ng/ml group and the...

06 February 2021 6,539 4 View

What mechanism is involved when chitosan is coated on magnetic nanoparticles?

Hello! I am currently working on coating of chitosan on magnetic Fe3O4 nanoparticles. I am wondering how this coating process happened? i.e. through what mechanism that chitosan can be coated on...

13 January 2021 5,657 5 View

The impact of different poisson's ratios when analysising field vibration?

The Poisson's ratio of soil is quite difficult for us geo-engineers to obtain. I came across a problem when I tried to determine the parameters in a FEM model. For the saturated clay in...

02 January 2021 8,971 3 View

Is it possible to deposition a large area dielectric layer(mm scale) on the wet transferred graphene?

I want to deposition a dielectric layer on top of the CVD wet transferred graphene. The purpose of the dielectric layer is to uniformly cover the graphene and enable the top-gate modification of...

14 December 2020 7,693 2 View

Is the fluorescent protein must be totally photobleached in FRAP assay?

Hi I have tried to measure the mobility of a protein of interest by the FRAP assay. The protein was fused with GFP. I overexpressed the fusion protein in Hela cells. However, when the area of the...

14 December 2020 6,567 1 View

Is there some effective transfection reagents or methods for transfecting plasmids to ExpiCHO-S cells?

Dear all, We want to transfect pCDH plasmid or other plasmids to suspension ExpiCHO-S cells and express our target proteins, and we used the transfection reagents PEI. Unfortunately, there...

26 November 2020 8,323 3 View

No title

The cell I used is 293T.I want to it can grow on the biocompatible materials,like agarose or alginate gels.But the shape of the cells is not good.In the T25 flask you will find the cell like...

26 November 2020 1,009 2 View

Again, what are the bands of extracted plasmid?

I used Trans1-T1 phage resistant chemically competent cells to extracted lentiviral gRNA expression vectors. And there were bands near 2000bp and smear on 1% argrose gel. Did the smear come from...

25 November 2020 858 2 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

Have anyone checked before Cyclic voltammograms of intial ITO substrate and E-teck?

As a beginner in electrochemistry, I tried to obtain cyclic voltamograms of commercial anatase powder deposited on an ITO substrate or on Eteck. After several attempts, I noticed that my cyclic...

23 February 2021 3,175 3 View

Fictitious Boundary Meshing Method (FBM) in Commercial FEA software?

Is it possible to implement FBM in a commercial FEA software package, such as FEMLAB, COMSOL, or open source software like Moose?

22 February 2021 2,968 1 View

What are the LAB methodologies (procedures, equipment etc) for CO2 enrichment experiments to study crop responses?

I am doing a proposal for a research entitled 'GRAIN YIELD AND QUALITY RESPONSES OF WHEAT GENOTYPES UNDER CO2 ENRICHMENT AND EXTREME EVENTS' I will be using climate chamber and I would like to...

18 February 2021 6,494 4 View

How to realize refractive index values of 1 to 1.1?

Hello researchers! While studying the literature on refractive index sensors, most of the articles simulate their devices with a refractive index ranging from 1 to 1.1, with small steps in...

17 February 2021 1,578 4 View