Whether micro-segregation of elements occurs in between steel shot and base material while perfoming shot peening process?

19 December 2018 1 8K Report

Chitaranjan Pany

shot-peening effect could be related to the grain distortion and to increased microstructural barriers.

Badges
Science topic

More Roshith .P's questions See All

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

Ti6Al4V - Phase differentiation between alpha and alpha prime martensite?

Dear Researchers, Is it feasible to distinguish between alpha and alpha prime martensite in the Ti6Al4V alloy under rapid solidification in the as-cast state using XRD, in addition to...

30 July 2024 3,849 0 View

How to interpret results of AST for Pseudomonas aeruginosa?

While doing AST for Pseudomonas aeruginosa, after incubation, no zone of inhibition observed in the plate near the well. wells surrounded by bacterial growth, when the same plate observed under UV...

25 July 2024 9,229 1 View

What is the Principle of Cysteine-carbazole-sulfuric acid reaction with glucose?

I have been looking for the principle of Cysteine-carbazole-sulfuric acid reaction in research papers and books, but couldn't find it. This reaction is mainly used for the quantification of...

23 July 2024 3,891 0 View

How can AI technology to enhance the agricultural productivity?

Farmers no longer have to apply water, fertilizers, and pesticides uniformly across entire fields. Instead, they can use the minimum quantities required and target very specific areas, or even...

22 July 2024 8,296 3 View

Can a paper that is posted as a preprint in a database with DOI, can be reviewed in another journal and accepted for publication??

It happened that I am asked to review a paper for a journal. Incidentally, the paper is posted as a preprint in another database as open access with DOI. It is completely citable. Now, should I...

17 July 2024 1,831 4 View

Do software tools exist to assess the economic and technical practicality of introducing new food products, such as yogurt with modified starch?

This question explores the world of food innovation and asks if there are computer programs that can analyze the financial and technical feasibility of introducing new food products. For instance,...

13 July 2024 7,446 0 View

How can I verify if an academic journal is a legitimate publication or a cloned version?

This question seeks to address the growing concern of cloned academic journals, which are fraudulent duplicates of legitimate publications. It aims to guide researchers, scholars, and academics on...

10 July 2024 5,966 2 View

To what extent Google Scholars Citations system is reliable?

1. I was shocked to discover yesterday that my research citations on Google Scholar had dropped to 2383 from 2419 a week ago, and they are now up to 2391. 2. My citations three months ago were...

28 June 2024 2,846 2 View

How can i calculate the band alignmet of Sc2CO2/BlueP heterostructure from DFT?

I know the work function and band gap of each monolayer and heterostructure. I calculated mulliken electronegativity(X) of Sc2CO2 and Bluep. From that i found Ev = X- 4.5+Eg Ec = Ev-Eg, where Eg...

28 June 2024 9,360 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

What is the mathematical expressionof theoretical yield strength calculated considering solution strengthening in stainless steel 316L?

In the expression for solid solution strengthening model that has been widely used in the literature use a linear form consisting of strength coefficient, and concentration of elements in wt.%....

11 July 2024 4,476 3 View

Why did the simulated load-displacement curve of beam keep increasing and didn't decrease (ABAQUS)?

Dear colleagues, I'm currently modelling a simple 4-point bending test of a concrete beam in Abaqus. However, the load-displacement curve was ascending (without final point), which didn't match...

29 June 2024 6,192 2 View

Methods of measuring the moisture content of iron pellets and iron concentrate in the steel industry?

Dear colleagues, I'm researching some methods of measuring the moisture of iron pellets and iron concentrate in the steel industry (especially non-contact methods). If you have any information...

22 June 2024 7,894 2 View