Whether it is possible to print a product using 3 different materials in 3D printing?

More Dinesh Babu Rathina's questions See All

1 nm thick MgO thin-film to be deposited on Si wafer using thermal evaporation. What will be the optimum deposition conditions?

Favourable conditions of base pressure, rate of deposition. Also, by which characterisation technique to be used to verify the thickness of the deposited film.

28 February 2021 3,640 3 View

Sensitivity analyze for crop evapotranspiration (ET0)?

Does anyone know how to perform a sensitivity analysis for crop evapotranspiration ( FAO Penman-Monteith equation) using daily meteorological data?

27 December 2020 9,552 3 View

How do I DERIVE equations for lumped elements (R, L, C) from S-parameters?

I have modeled the lumped element circuit for the 3D structure which has been simulated in HFSS. Now I need to derive the equations for the lumped elements keeping the S-parameters of the...

23 December 2020 172 3 View

No title

For academic writing.

17 December 2020 6,465 5 View

How to get nanocomposite of PEEK with Zirconia ?

Need a lengthy PEEK with Zirconia based nano composite of 180 mm length. Which method is possible? Tried injection molding no proper mix. Solvent casting process is also very costly. Kindly anyone...

13 December 2020 4,329 5 View

Choice of sampling time in discretization of control?

What I understand is while applying continuous control to a continuous-time system in MATLAB simulations, actually the control is being applied in discrete manner inherently due to the nature of...

28 November 2020 1,866 4 View

Simulation of sliding mode control for a maglev system?

I tried to simulate a maglev system with continuous time sliding mode but my simulation is showing error (there is a singularity at one of the integrators). I am attaching the modelling and...

16 November 2020 8,964 7 View

Can anyone suggest is there any way to compare the amount of chattering in 2 approaches of sliding mode control in quantitative way physically ?

Suppose 2 methods are shown to do sliding mode control of a given system. Please tell me if we can compare chattering in both by MATLAB or some other way

16 November 2020 3,251 3 View

How can I get eggs of an univoltine casebearer moth for a threshold study?

I am planning to conduct a cage study to determine a critical density of an univoltine casebearer moth in red clover seed crop. This requires to release first instar larvae in the cages with the...

02 November 2020 6,577 3 View

Can anyone suggest me free and fast scopus publication with highly acceptance rate?

Q3,Q4 will be okay. I need scopus publication without APC and fast published. The paper is from Computer science discipline.

19 October 2020 4,255 4 View

What is Nano technology with coronavirus helpe the human..and is it nano mterals removal of covid19?

I anwar by adsorption or reaction ..but it is either more method...

02 March 2021 4,811 2 View

How to compare different concentrations of nanoparticles for characterization from ICP-MS?

I took measurements of different concentrations of 15 nm and 5 nm Au nano particle solutions. I'm trying to determine which concentration I measured gives the best reading overall. I also...

02 March 2021 7,626 1 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Zno nano particles colour changed from white to grey in process of calcination any suggestions?

In the formation of Zno nano particles process, after drying at 120 degree C, my zno nano particles are completely white but when i calcine it for 450 degree C it converts into grey colour. i...

26 February 2021 2,435 4 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

I am looking for a simple software program to model 3D chemical bonds. The purpose is to generate high-quality graphical abstracts. Any suggestion?

Hello everyone: I am looking for a simple software program to model chemical bonds. The purpose is to generate a high-quality graphical abstract for a top leading journal in the field of...

23 February 2021 8,012 3 View

Which programs are to be used to register 2D image onto a 3D image data set?

I am trying to register a light micrograph onto a 3D CT data set, as I want to extract the corresponding image from the CT data set. Is there any software or program can do this accurately? I am...

21 February 2021 8,220 3 View

What is the better software for approximation of 3D surface with equations?

I have a massive of x, y, z coordinates of 2D surface in 3D space, which builded in Ansys HFSS or AutoCAD. How can I get the analitical aproximation of this surface by formulas?

21 February 2021 3,444 7 View

How can I obtain Reaction Forces in ABAQUS?

I am trying to simulate a simplified version of a beam resting on 10 points using Abaqus. The solutions I want to obtain are the Reaction Forces in each resting point or area when applying a...

21 February 2021 3,075 2 View

What is difference between In-line transmission (%) and Total transmission (%) value of optically transparent Ceramics?

I am working on transparent/translucent zirconia-based ceramics. In many papers, I have seen that they are reporting both In-line transmission (%) & Total transmission (%) value of...

20 February 2021 9,405 6 View