In frequency domain alpha band(8-16hz), beta band(16-32hz), gamma band(32-64hz), sub-band(64-128hz) are same as LL,LH,HL,HH in wavelet decomposition?

I am working on single trial motor imagery data i.e. EEG data. I am following a paper which has a dataset from BCI challenge IV (dataset 2b). After removing noise and extracting all the data from...

23 February 2021 5,503 1 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

No title

The Folin-Ciocalteu method is an electron transfer based assay, and gives reducing capacity, which is usually expressed as phenolic content. Can anyone share any reference paper where total...

13 February 2021 3,782 3 View

How to compare two group with small sample size (n=3)?

I am working on some physiological traits of plant to which its expensive to raise the sample size beyond n=3. so kindly suggest some test which is applicable to test such group(2)

04 February 2021 461 11 View

Is it possible to find out the wettability and contact angle of water on the rough or corrugated substrate?

First of all, whether it is possible to identify the presence of water and its amount on the Silicon substrate by using only FT-IR spectroscopy. Can ATR-FTIR spectroscopy find out the wettability...

03 February 2021 9,085 4 View

How to find statistical data of EEG signals?

Hi all, I hope everyone is doing good. I am working on Machine Learning, I am working on EEG data for which I have to extract statistical features of the data. Using mne library I have extracted...

29 January 2021 6,686 1 View

Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

Multicollinearity between bioclimatic variables in spatial distribution modelling?

Is there any manual guide to perform multicollinearity test between environmental (19 Bioclimatic) variables for MaxEnt modelling? Using all variables without removing the correlated one affects...

14 January 2021 3,807 7 View

How or from where can I get energy load profiles for the household, tertiary and industrial sectors specifically for EU27 countries?

Dear Researchers, I am looking for time series or a function to generate yearly, monthly or daily load profiles for the sectors such as household, tertiary and industrial. These load profile must...

11 January 2021 2,307 2 View

Please share some research papers on the synthesis of Mn3O4 nanoparticles via Hydrothermal method by using Manganese(II) nitrate hydrate?

05 January 2021 9,040 4 View

How to repeat an operation on an atom selection for multiple times in PyMol?

Hi, I am trying to construct a multi-layer fibril structure from a single layer in PyMol by translating the layer along the fibril axis. For now, I am able to use the Translate command in PyMol...

02 March 2021 4,569 4 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

Bayesian decision trees and bayesian regression trees in Python and/or R?

I am looking for implementation of bayesian decision trees and bayesian regression trees in Python and/or R.. Do you know if the existing libraries support this

23 February 2021 6,689 3 View

How can we estimate sample size for a moderated mediation analysis with more than two mediators?

How can we estimate sample size for a moderated mediation analysis with more than two mediators? I am looking for scripts, macros, syntaxes, that allow us to estimate sample sizes for research...

15 February 2021 6,813 3 View

In Abaqus, is it possible to remove elements which are too complex for meshing from a sequence obtained by getByBoundingBox() ?

Hello everyone, I'm trying to mesh a structure with complex partitions using mesh controls. When doing it on the user interface I'm first selecting all cells. In the following, I have to accept...

03 February 2021 8,198 1 View

How to calculate j-integral for 5 contours by abaqus script and retrieve the values ?

I mean I am looking for a code to retrieve the values of each contours and I have written the code below but It doesn't work... Jint= odb.steps['Step-1'].historyRegions['Assembly...

21 January 2021 277 3 View

How to add a single parameter in Ansys Additive Manufacturing Workbench parameter setting dialogue box?

Ansys 19.2 R2 and 2020 R1 versions of Additive Manufacturing Workbench is convenient for powder-based Additive Manufacturing processing. However, in this workbench, there is a machine parameter...

19 January 2021 3,017 2 View

How to script VMD tcl within bash script?

Greetings, I want to run a vmd script within my bash script. I am using the text only version of VMD for linux for my windows terminal ubuntu subsystem and I would like to generate code within my...

16 January 2021 192 5 View

Can anyone helps me with Autodock 4.2 scripts error ?

After opening the file, I operate command "Script" --> "Ligand Interactions" --> "Show Ligand Binding Site Atoms" and the warning appears as "This script displays ligands and surrounding...

15 January 2021 5,360 1 View

No title

Hi there! I'm very new to r and trying to run a multi-level meta analysis using pre-calculated effect sizes. I've attached the datafile below. The script I used as a first step to fit the model...

12 January 2021 8,214 2 View