How can I measure MMP-1 protein activity or protein level from liver tissue?

Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?

03 March 2021 1,763 2 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Looking for Materials with high thermal expansion coefficient and high temperature resistance?

03 March 2021 8,272 1 View

Guidelines for survey (question type) analysis?

Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...

03 March 2021 2,037 3 View

What are the values needed for gabor filter's parameter for cifar10 data?

Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...

03 March 2021 6,317 1 View

Can we block unwanted images during the x-ray prediction?

i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).

03 March 2021 7,100 1 View

No title

03 March 2021 5,360 2 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

The procedure compute?

02 March 2021 5,204 3 View

How to remove the residual PDMS on the silicon mold?

Incompletely cross-linked pdms are difficult to remove.

01 March 2021 798 3 View

What is the best solvent to remove PDMS from nano particles?

I want to remove PDMS oligomers from the surface of nanolayers. I have just read a very helpful paper about the compatibility of PDMS with different solvents( Solvent Compatibility of...

24 February 2021 7,845 5 View

How to determine solutionizing time for cast Al alloys?

For wrought alloys soaking time at solutionizing temperature is determined by thickness .Do we have such standards for cast Al alloys

23 February 2021 8,839 3 View

What are the main conditions suited for synthesizing a PVDF thin film by solvent casting method?

I have been trying to synthesize PVDF thin film by solvent casting method. I started by using 2:3 DMSO: acetone as solvents. The solution was stirred for 3hrs at 60 deg and was dried at 90 degrees...

09 February 2021 8,850 3 View

How can I convert permeability unit from barrer to m^2 for using COMSOL MultiPhysics?

I am looking for gas permeability of PDMS for simulation in COMSOL MultiPhysics and using creeping flow , fluid and matrix properties. The permeability unit in COMSOL is m^2 whereas I have the...

08 February 2021 4,305 2 View

Is it possible to economically reuse the heat content of water vapour that is generated during quenching of continuous casting of steel?

A huge amount of water is evaporated to cool down and solidify the liquid metal strands coming out of bottom of CCM mould. The steam contains significant latent and sensible heat energy, besides...

26 January 2021 3,446 4 View

Is it possible to highly selective remove a fused silica template from PDMS by laser-induced backside wet etching (LIBWE) method?

Hi everyone I'm trying to pattern circular cross-section microfluidic channels in PDMS. The template is an optical fiber with an axially non-uniform diameter. To the best of my knowledge, there...

22 January 2021 2,352 2 View

Is it possible to deposit very thin metal traces on a thin film of PDMS with long term durability?

Hi all researchers, I have been working on a research project where I need to fabricate very thin traces of the metal on a thin film of PDMS that can withstand large number of loading and...

06 January 2021 284 5 View

Is any way or method to seal agarose pad or channels fabricated agarose gel pad to glass slides as like we do plasma bonding with PDMS to slides?

Is any way or method to seal agarose pad or channels fabricated agarose gel pad to glass slides as like we do plasma bonding with PDMS to glass slides?.

04 January 2021 3,589 2 View

Vhb 4910 and carbon black as a electrode have some diference between carbon with pdms?

There is a dopant for the vhb 4910 actuator tapes that have acetylene black or carbon black which is carbon grease (carbon black + pdms) commercially, I am making a robotic actuator but I don't...

30 December 2020 3,144 1 View