How to Control Whiteflies in coconut leaves?

24 February 2021 1,005 1 View

Are there any exception like work hardening in metals elastic limit due to dynamic loading?

The samples made out of spring steel are taken from same lot. The specimens were shaped following heating to forging temperature - Forming- Hardening -Tempering methods. After storage of almost 6...

11 February 2021 952 6 View

Regarding to presentation of pairwise comparison of data?

22 January 2021 8,648 1 View

What is the main advantage of using observer based fault tolerant controller(FTC) for sensor fault tolerance?

I am working on FTC for handling sensor faults in the system. I have read about observer-based FTC schemes which use error threshold-based logic between the states and estimated states. If a...

10 January 2021 5,771 2 View

Can a luenberger observer (even a modified version) be effective for a nonlinear affine system?

I want to know whether a luenberger observer or a modified form of it be effective for estimating the states of a system of the following forms: 1. x_dot = f(x,u,d); y = x 2. x_dot = f(x,u); y =...

20 December 2020 1,392 4 View

How can I control Asphodelous tenuipholius in chickpea and mustard crop. Any effective post emergence herbicide?

In Bundelkhand region of Central India, Asphodelous tenuipholius is major problamatic weeds on farmers field. Any suggestions from weed scientists

29 November 2020 1,207 4 View

How much Tensile strength and hardness can be acheived in Aluminium 7050 MMC with B4C reinforcement?

I have conducted research on characterisation of Al7050 + B4C by electromagnetic stir casting. The alloy employed in the process is casted alloy and the Composite too is casted. How much strength...

16 November 2020 9,226 3 View

Why whitefly prefer not to infest Pigeonpea?

Whitefly, Bemisia tabaci is pest of broad host range. In pulse crops, it generally infests greengram, blackgram and cowpea but not Pigeonpea. There might be some biochemical or morphological...

09 November 2020 9,199 3 View

Can u suggest how to identify the matrix material and reinforcement particle distribution in the MMC of scanning electron miroscopy (SEM) images?

How to identify the reinforcement particle behavior in SEM images

09 November 2020 8,664 3 View

Effect of excess cyclodextrin on drug after cyclodextrin reaches maximum solubility in phase solubility study?

I am working on phase solubility studies between beta-cyclodextrin and drug? I used more concentration of beta-cyclodextrin till 30mM despite its maximum solubility of 16mM. Usually, above maximum...

30 October 2020 3,921 9 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

LEDs on Vis Light photo degradation of MB water sol via N doped TiO2 in a mini flume?

Good day to all, I have no experience with light emitting diodes. I am building a glass mini flume to demonstrate the photo degradation of Methylene Blue in water running over self cleaning...

26 February 2021 4,026 5 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

To date, according to health authorities, 30% of the population's diseases are initiated by drinking water pollution. Do you know this problem?

The main studies are as follows: * regular and timely receipt of information about the state of the environment using automated systems (stationary and mobile); * operational analysis of the...

23 February 2021 912 5 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

How to find the air side pressure drop in a spiral fin tube bundle cross flow heat exchanger?

How to find the air side pressure drop in a spiral fin cross flow heat exchanger? The pressure difference at the inlet and outlet is very low compared to the experimental results, which I...

18 February 2021 1,109 2 View