When I add Error bar on my statistics, I am not sure which one I should use, SE or SEM?

12 December 2016 0 3K Report

when should we use SE and when should we use SEM? Do they have some specific requirement, if you want publish your paper?

Badges
Science topic

More Liang Yusheng's questions See All

When you are generating a standard curve what should you pay attention to?

before we doing the relative quantitative real-time PCR, we should generate a standard curve. when we are generating the standard curve what should we pay attention to to make your curve more...

11 December 2016 2,689 7 View

If the primers have been used in other papers anddo you have to do the standard curve and calculate the amplification efficiency?

if the primers have been used in other papers and you want to cite these primers in your paper for relative quantitative real time PCR, do you have to do the standard curve and calculate the...

10 November 2016 2,097 6 View

Is it necessary to do the standard curve before we conduct the relative quantitative real-time PCR for microorganism?

what is the prerequisite before you conduct relative quantative real-time PCR?

10 November 2016 9,292 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

How to learn more about SPSS and its Application?

I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.

11 August 2024 9,101 4 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Has anyone applied Python in the field of textile engineering for data analysis, automation, or smart textiles?

I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...

10 August 2024 7,429 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Do I need specific antibodies to stain for a fusion protein?

I am staining some brain sections stored in cryoprotectant that express a Histone H2B- GFP fusion protein that were generated ~10 years ago. I know I need to enhance signal with an anti-GFP...

07 August 2024 5,338 2 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View