When do you accept someone is competent in performing percutaneous tracheostomy? Are there any recommended standards to maintain this competency?

More Palanikumar Saravanan's questions See All

What could be the possible reason for the drastic variation in Qmax value for same adsorbent onto two different cationic dyes itself?

The adsorption capacity of the rice husk biochar was varying drastically with two cationic dyes namely Basic Blue 41 and Basic Red 09? What could be the possible reason behind this?

30 January 2021 1,420 3 View

Formula to determine the length of piping required for heated N2 gas?

Heated Nitrogen gas will be allowed to flow through stainless steel piping as part of my project.Hence, I need help to generate a formula in excel to calculate the length of piping required for...

17 August 2020 2,031 5 View

Which software is best to plot paleoclimate data with high resolution?

Dear All, I'd like to plot high-resolution figures of paleoclimate data, Please suggest the best and most friendly software. Advance thanks, Saravanan

25 July 2020 3,003 6 View

Why ellipsometer spectrum of silicon nitride (SixNx) shows the number of peaks at 530 nm excitation wavelength?

We have deposited the silicon nitride (SixNx) on the silicon (Si) substrate using atmospheric pressure chemical vapor deposition (APCVD) technique. After the measurements, the ellipsometer results...

03 January 2020 1,400 3 View

Is there any upadate in List of Journals in JCR 2019?

Journal indexed in web of science JCR 2018 is attached . Can any one tell me any updates in JCR report 2019

27 April 2019 7,306 3 View

Why XRD pattern of ZnO nanorods prepared on FTO glass by electrochemical deposition is different than the others?

We have attempted to prepare nanorods on FTO plate by electrochemical deposition. In general XRD pattern of ZnO yields 2 theta 31, 34, 37 corresponding to (100), (101) and (002) planes. In our...

18 March 2019 7,633 4 View

How to do multi-step analysis in Abaqus?

I am doing bolt load and torque load sequentially. But not sure that my result going to valid.

28 January 2019 8,965 3 View

How much powerful BLDC motor do I need for my 200 kg motor bike?

Hi, I have a motorbike weighing 200 Kg, running with IC engine, Now I intend to convert it electric using BLDC, I aim top speed of 80 kmph, and no problem with acceleration it can as low as...

19 September 2018 8,718 7 View

Can Magneto-rheological fluids simulation be done using ANSYS?

I want to know whether analysis and simulation of magneto-rheological fluids be done using ANSYS software?

18 June 2018 8,305 3 View

Which ayurvedhic diabetic drug is not scientifically proved?

I am planning to work on the integration of ayurvedic drug and allopathic system using an animal model. So kindly suggest good ayurvedic or herbal medicine for the treatment of diabetes but which...

27 July 2017 8,891 4 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

How the parameters (such as Mw, Chemical bonds, polymer bland and so on) affect the mechanic property of polymer (such as storage, loss modulus) ?

Anyone can recommend any books on such topics? Thanks in advance.

02 March 2021 8,457 2 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

Does the circuit modeling for planar monopole antennas using Foster canonical forms give good approximation?

Hi researchers, I am searching for some accurate way to do the circuit modeling of planar CPW-fed monopole antennas. I have gone through the literature where mostly circuit modeling is done using...

28 February 2021 7,016 1 View

Which is better medicine or food in obesity?

Preference in terms of the scientific aspect

28 February 2021 796 2 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

How can I verify my centrifugal fan design for electric motor cooling?

I have radial blade centrifugal fan design which will be mounted on exhaust side of electric traction motor. The fan will be mounted on same motor shaft inside the housing. How can I verify that...

23 February 2021 2,390 3 View

Why cannot world and community leaders be gentle? Where did ethics of care go?

The whole world is in a mess and paused. We all are tired of seeing hypermasculinized and destructive leaderships all around us. This world has seen enough of the aggressive patriarchal social...

23 February 2021 292 7 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

How to use Remote sensing and GIS applications for mapping the available medicinal plants within the locality/municipality?

Hello, I'm very interested in mapping and managing the conservation of the Philippine traditional medicinal plants, in which I think is very helpful in the field of medicine for further analysis...

21 February 2021 374 5 View

Walter Mauritz

There are no standards, as far as I know. We have trainees providing assistance in 5 cases, and then have them do one closely supervised. The techniques are not that difficult, and easily learnt. After another 10 supervised cases, trainees are able to do this on their own.

Alisa Krdzalic

Not so dificult,.In our depatrement anesthesiologist to do percutaneous tracheostomy. I agree- 5-10 supervised is enough to independently work.