What would be the Reynolds number for such an external viscous Koch snowflake flow?

20 October 2016 1 5K Report

I think it's possible to find a rational answer to this question, but I do not have (the answer). Intuitively I think that this bizarre type of flow has fixed Reynolds number and equal to infinity (Re=infinitum), for any boundary conditions.

Zoubair Boulahia

Look at this doc it may be helpul for your topic. Good luck.

Badges
Science topic

More J.I.H. Lopez's questions See All

Samples to study circular dichroism (chirality)?

I want to build a low-cost polarimeter to study circular dichroism (chirality). What type of samples can I use? I am looking for samples that can be found outside the laboratory.

01 March 2021 9,101 3 View

Which cell line should we use to perform biological dosimetry experiments?

We are preparing some experiments based on irradiating cells under different conditions in order to evaluate the effects in terms of DNA damage, genetic expression, etc. As our project is...

01 March 2021 3,355 3 View

RIA. How to measure?

When you use RIA, with a control the unknown sample with antibodies, you bare in mind the binding sites of the antibodies. However you still need to measure labelled antigen (radioactive) and not...

28 February 2021 2,133 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

Algorithms to filter corrective max and min from a set of data?

I've got this 5 year Direct Normal Irradiance data I downloaded from https://re.jrc.ec.europa.eu/. I ordered this by year and by every 24 hours because I need the DNI curve by max in summer, min...

17 February 2021 2,777 5 View

Flexibility of RNAseq?

When you use RNAseq I understand that it must follow certain conditions when you use it. One of them is the insertion of a polyA tail. The insertion of the polyA must include then...

05 February 2021 3,770 4 View

Is there an open source tool the measures the GRAVY index of a peptide incorporating the PTMs and unusual amino acids (e.g. hydroxyproline)?

Right now, I am using ProtParam to compute GRAVY index of peptides. However, some of my peptides are post-translationally modified, and contains unusual amino acids. I assume that ProtParam does...

29 January 2021 8,300 4 View

What type of spectral radiation has greater penetration on materials, UV or IR? What book or source do you recommend for information on this?

I need information concerning the penetration and reflection capacity of ultraviolet and infrared radiation wavelengths on different most common materials. Edit. Can somebody recommend a book to...

16 January 2021 8,051 6 View

Could be estimate or simulated the electrical properties of thin films obtained from new organo-metallic compounds?

In the context of synthesized organo-metallic compounds, I am interested in the formation of thin-films over silicon wafers. Among another characteristics to be investigated, electric properties...

13 January 2021 7,575 2 View

How long does the peptide cleavage cocktail last before it gets expired?

The cleavage cocktail is composed of Phenol/thioanisole/water/TFA/triisopropylsilane. I only prepare 10 mL cocktail per peptide but can the activity of the cocktail prepared at 100 mL last for a week?

10 January 2021 7,424 3 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Joint behaviour in Abaqus is not captured well?

I am working on roof joint and trying to simulate the behaviour in Abaqus. I am successful in running the model but the final graph does not follow the experimental curve in the negative direction...

01 March 2021 6,661 3 View

Can we distinguish the type of free fluid inside the pelvic and abdominal cavities whether blood or serous fluid using the ultrasound?

during ultrasound examination of acute abdomen, sometimes we see free fluid , can we know the type of fluid ,whether blood or not , using ultrasound only? if yes , what are the sonographic...

01 March 2021 7,476 4 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Is there a deep reason for using the squared modulus of the wave function as the probability density of the existence of the particle?

I think we were all surprised at the first time we got to know quantum mechanics that the squared modulus of the wave function is the probability density of the existence of the particle? The role...

28 February 2021 6,282 9 View

How to modify Johnson cook equation in ABAQUS?

I wanted to add an extra parameter to the existing Johnson cook equation in the ABAQUS simulation. How to add those extra parameters. Ref: A modified Johnson-Cook material model with strain...

28 February 2021 4,841 3 View

How can we simulate an hyperelastic-viscoelastic behavor with Ansys APDL?

I am working on modeling and simulation of biomecanical material behaviour, I have succeded on simulating skin using anisotropic hyperelastic material, on APDL and in our lab's finite element...

28 February 2021 552 3 View