16 May 2022 0 5K Report

Flow Controlled Resin Bath in the filament winding process (No flow control devices are observed, then what will be its effect on the process?).

More Jigneshkumar Parmar's questions See All
Can any suggest me good method of GC MS for the separation of Flavonoids?

I prepared the ethyl acetate, ethanol and butanol fraction from the ethanol extract of seed for isolation of Flavonoids. Amongst them ethanol fraction showing shinoda test positive for polar...

13 February 2021 8,263 3 View

Any specific reason, how sclerotium rolfsii can grow out of Petridish?

Is it related to nutrition or any other reason? Any other fungus have similar kind of growth pattern?

09 February 2021 4,357 4 View

How we can dissolve highly insoluble compounds in solvent such as DMSO, WATER, MeOH etc.?

We have tried all the aforementioned solvent with heating. So please share your thoughts how can we soluble my compounds.

14 May 2020 4,208 21 View

What is the difference between Power Transformer Fault Current And Sub Station Fault Level?

What is the reason of Transformer Fault Current is always lower then System fault level?

17 March 2020 2,854 3 View

Is there any method for the isolation of Taphrina maculans causing turmeric Leaf blotch?

Also mention media, pH, temperature and other conditions required for the isolation.

19 October 2019 1,505 2 View

What is the average weight of hypothalamus in Rat?

Hi all, please help me with this question. Thanks a lot in advance!

18 April 2019 4,305 3 View

What things should be taken care of, while performing immunohistochemistry of phospho proteins?

I am doing IHC for normal proteins, but there must be a different protocol to treat phospho proteins. Please, enlighten me with that. Thanks!

02 August 2017 7,414 2 View

How to use cell counting plugin in Image J?

I need to count nerve cells in the tissue stained with Cresyl violet. Please provide me guide to make us of Image J software for cell counting. I have cell counter plugin in Image, but I don't...

01 August 2017 9,887 2 View

Which material gives higher buckling load CFRP or Aluminium?

I am currently conducting research on the buckling of thin plates and simulating a range of materials in abaqus. It seems according to my results that Aluminium gives a higher buckling load...

26 July 2017 9,697 4 View

What boundary conditions do you recommend for a simply supported thin plate under compression?

I am using Abaqus to simulate, the initial boundary conditions which i have tried, is giving me a error of 32% with the theoretical solution. And this is for buckling analysis.

06 June 2017 6,663 3 View

Similar questions and discussions
What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How optimize the Size Exclusion Chromatography?

Hello! I'll do a size exclusion chromatography, but I only have an open column, and I'll perform the peptide extraction from yeast, using buffer lysis (sodium phosphate 50 mM/NaCl 30 mM/DNAse and...

01 March 2021 2,215 2 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Isolates of Hymenoscyphus fraxineus?

Dear Dr. Cai, my name is Simone Prospero and I work in the team of Phytopathology at the Swiss Federal Institute for Forest Snow and Landscape Research (WSL;...

01 March 2021 1,133 1 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

For modelling epoxy-based matrices (in composites), which model in ABAQUS is the most suitable, Concrete damaged plasticity or Drucker-Prager model?

I am working on developing a micromechanical FE model for predicting kink-band formation in UD composites. To model matrix plasticity, which model, out of Concrete Damaged Plasticity and...

28 February 2021 5,415 1 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close