What was the size of bottle used?

Ertug Aydin @Ertug_Aydin

01 January 1970 0 1K Report

I was used waste bottled in mortar and cement paste. What do you think about the powdered form?

Badges
Science topic

More Ertug Aydin's questions See All

What type of tests do you suggested?

Shall we characterize by using non destructive instruments?

01 January 1970 5,636 0 View

How can you investigate the environmental actions?

Which tests will you use?

01 January 1970 9,215 4 View

What is the depth of measurement?

Is there any limitations for measurements?

01 January 1970 1,147 4 View

How do you produce geopolymer at laboratory?

What was the mix design parameters in the project?

01 January 1970 8,800 4 View

Do you planning to perform test for sulfate resistance?

Do you consider testing periods after 56 days?

01 January 1970 2,359 4 View

Do you measure chemical resistance?

what do you think for the chemical resitance of the waste ceramic materials?

01 January 1970 8,384 4 View

What was the optimum percentage for demolished wastes?

Shall we used as a cement replacemet?

01 January 1970 7,069 6 View

Do you advice non destructive measurements?

There are non destructive methods for measuring the chloride resistance. Do you advice such measurements?

01 January 1970 6,246 1 View

Which tests do you performed?

shall we use non destructive methods?

01 January 1970 281 2 View

How to dispose off lipids waste?

I am looking for a lipid waste disposal method, keeping in mind the environmental, health and safety aspect of lipid waste. Could someone please provide guidelines or the lowest acceptable...

25 July 2024 637 5 View

Mechanochemistry: ball to powder mass or ball to powder volume?

I run mechanochemical reactions that involves the use of a large amount of catalyst (1:1 molar ratio to the reactant). When I try to understand the effect of amount of catalyst on the reaction, I...

23 July 2024 9,938 1 View

What are the effects of coffee husks waste to the environment ?

Coffee waste

16 July 2024 1,303 3 View

I want to plot calibration curve of pure mirtazapine powder using HPLC. Can someone please suggest a method without HPLC buffer as a mobile phase?

I am searching for HPLC method to estimate Mirtazapine but i want to avoid HPLC-buffers as a mobile phase component. So, I am looking for alternative HPLC-solvent (acetonitrile, methanol etc.)...

14 July 2024 1,493 3 View

What binders suggestion that I can use for zinc alloy?

I am working on powder metallurgy, and during the compaction process, the powder does not pelletize and remains in its powder form. To address this issue, I am considering using binders to improve...

13 July 2024 9,003 2 View

Quelles applications innovantes peuvent bénéficier des propriétés des géopolymère?

Les géopolymères offrent plusieurs propriétés intéressantes qui peuvent être exploitées dans diverses applications innovantes : 1. Construction durable : - Bétons à faible empreinte carbone -...

10 July 2024 7,457 1 View

How i figuer out the weight of curcumin powder?

I am trying to load curcumin emulsion in 4% chitosan gel but i don not know how many mg powder is needed ?

10 July 2024 2,462 1 View

Can anyone suggest what amount of powder I have to disperse in the solvent for taking the FTIR spectra?

I have to compare the FTIR of the two samples, one is in powder form and other one is the powder dispersed in IPA or water. Both are same material, so how the bond will change

09 July 2024 8,011 2 View

Is VSM measurment of NdFeB alloy powder sample require any spesific sample preparation ?

Is any specific sample preparation required to perform VSM measurement of NdFeB alloy powder to get a square-shaped M-H loop? Or is it mandatory to make magnetically aligned and sintered pellets...

09 July 2024 1,969 0 View

I have need a LPBF/SLM model on comsol multiphysics ?

In this model clearly understanding how to active one layer to another layer and how to add powder material properties step by step.

08 July 2024 6,147 0 View