What type of nano-material coat will help in improving the solar panel efficiency?

More B P Patil's questions See All

What are the chemicals coats which can be used for enhancing the efficiency of solar panel?

It is found that chemical coat will improve efficiency of solar panel. Let me know which is more effective and why? Thanks

05 June 2018 4,231 4 View

How to minimise location error (to few centrimeter level) for indoor location system?

Currently this accuracy is close to 30-40 centimeter. Further it needs to be improved. What are the different improvement algorithms / techniques which are available if any body know pl. share...

11 December 2015 5,595 6 View

Adhesion strength of coating?

How can I determine a good adhesion strength range for coatings on polymer surfaces, such as DLC on polymer substrates? Is there a specific threshold for adhesion strength (from T-peel tests)...

10 August 2024 942 3 View

How do I conformally do PR spin coating on trench structure?

I did PR spin coating on trench structure. I used AZ P4620 PR and the thickness or PR is around 11um. The substrate is Si. And my trench structure depth is 141um(negative way). Even though I...

08 August 2024 2,298 0 View

What is the solvent for 8YSZ nano material?

I need to do some experiment with it in liquid form.

07 August 2024 613 3 View

Why do i have a weak plasma and no coating during rf sputtering?

I have been getting a low plasma and no coating while doing rf sputtering of copper doped ZnS using a power of 140 watts and at pressure of 6.5x10-3 Mb.

07 August 2024 4,526 4 View

What is the reason I get 400nm nanoparticles using an extruder with 200 nm membrane for cell membrane coating?

I am trying to coat my micelles and PLGA based nanoparticles with cell membrane using an Avanti mini extruder according to literature . I use 200nm membrane but my particles end up to be 400nm And...

30 July 2024 3,294 3 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How do you get pure primary macrophage cell culture?

I have been harvesting monocyte-derived macrophages from buffalo and cattle fresh whole blood using the same protocol for years and getting good macrophage cultures. Below is the protocol that I...

23 July 2024 4,074 2 View

Issues in coating of cathode material on Al foil, why we are not getting proper coating and results when the cathode was coated on Al-foil..?

We are trying to coat some cathode materials on Al-foil ( ex - LiFePO4 , S@CNT, etc). When we coated the Al foil with the cathode (ex - S@CNT) material , the cycling result was annoying. But the...

09 July 2024 5,123 4 View

Why NCM cathode slurry has coating problem?

I tried to make slurry for NCM cathode but there was problem in coating process. The detail of my experiment is following; The ratio between active material(NCM811), conductive additives(Super-P)...

08 July 2024 7,327 4 View

Why can't we get on top of this incubator infection (fungal)?

We have been experiencing repeated what looks very much like fungal contaminations in several incubators (in the same lab). We have tried the following repeated times and yet the coating on all...

02 July 2024 6,375 2 View

Luma M. Ahmed

ZnS nanoparticle....

Ahmed Hmeed

i am interested

Majibul Babu

Dear B P Patil

I think Copper Indium Diselenide, Cadmium Telluride and Gallium Arsenide will be best for the solar cell panel. You can go through the following attached link:

https://www.azooptics.com/Article.aspx?ArticleID=147