What should be expected error in mass balance in cross flow condenser?

More Parnab Saha's questions See All

Is this 6GHz wifi antenna create complexity at the time of febrication?

I have design a 6GHz antenna for wifi.The feed line width is 2mm and there are 2 parasitic elements beside this feed line with 1 mm gap.Is there any problem at the time of febrication?

04 February 2021 9,241 3 View

How can you make a PEDOT:PSS film using the doctor blade technique?

I have been trying to make an even PEDOT: PSS (PH1000) film with the doctor blade technique (tape casting) with varying results. I have been using a silicon substrate that's treated with piranha...

01 February 2021 8,506 5 View

How robust are open source soil moisture sensors connected to an arduino board for field monitoring?

Seeking recent experiences in the development and deployment of low-cost soil moisture sensors (ideally under $50/sensor) connected to arduino-based dataloggers. What is the longetivity of the...

19 January 2021 6,256 2 View

How to separate a mixture of organic acids by GC?

I would like to develop a method for analysis of many organic acids in the same time. how to separate the chromatographic peaks of each one?

20 December 2020 8,399 3 View

Should I keep the missing values > 50%?

I have a data set of 771 sample size. But some of the variables (laboratory findings like ALT, AST, creatinie level) have more than 50% missing values. Should I drop those? But I think those...

13 December 2020 4,847 3 View

How to Strip off HSQ( Fox 16) after etching?

We are finding a hard time to strip of residual HSQ ( Fox 16) after using it as a mask in etching? We are coating 600 nm thick HSQ and writing with 3000 microC/cm^2 dose at 1 nA current. We are...

08 December 2020 5,452 2 View

Why the oral cancer cell line from metastatic tongue origin is showing less aggressive property?

I am working with oral cancer cell line SCC090 (ATCC). As per ATCC data sheet it is originated from metastatic tongue. It's primary site is not mentioned. Due to the origination from metastatic...

08 December 2020 5,674 3 View

In case of larger sample size (more than 700 sample) can I do t-test though the data is not normally distributed?

My sample size is more than 750 but sk test is showing non-normal distribution. The variables have several outliers but I shouldn't remove those. In that case what should I do? t-test or other...

06 December 2020 1,285 19 View

Why the western blot of HIF1alpha of the whole cell lysate shows intense band under normoxia without any induction of hypoxia?

I am working with oral cancer cell lines and trying to find the expressional changes of HIF1alpha under different experimental treatment. I am getting intense band of HIF1alpha in the western blot...

29 November 2020 5,707 3 View

How to calculate in-plane lattice strain for 2D material?

I am working with h-BN and need to find out the strain due to in-plane lattice constant. The famous Williamson-Hall method may not be applicable here as it analyzes XRD for calculation of strain...

19 October 2020 7,386 4 View

After a reference from Int J Body Compos Res, can any body help?

Hi, I am after the reference below, my library says it cannot obtain a copy either locally or internationally, any help appreciated! Chris Wang ZM, Heshka S, Wielopolski L, Pi-Sunyer FX, Pierson...

03 March 2021 6,193 1 View

How to code open-ended questions in SPSS?

Hello all, In SPSS I am going to code 2 open-ended questions. I have already read all the answers and I made a list of the most important categories to which I can code the answers. This question...

02 March 2021 1,757 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why the results when using wall thickness and when using shell conduction are different in ansys fluent?

Actually, I am running cfd simulation for a heat exchanger which has two fluids one hot and other one is cold fluid. there is a solid domain between them, which I removed and instead I have used...

01 March 2021 9,537 2 View

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

Can Virtual Servers (remote dekstop manager) run heavy ANSYS Fluent CFD simulation ?

I have a virtual machine. My host Pc specs are not that good thats why i went for virtual servers. so basically my host pc has 8gb of ram with nvidia quadro k2200 4Gb DDR5 GPU ,processor intel...

01 March 2021 8,415 1 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

How to eliminate Steady state error from Reinforcement learning genetic algorithm code?

The following code (see 1st 2 images attached) is used to produce PID controller values that are designed to control the system (G). The code finds the PID controller values (noted as k) by using...

28 February 2021 6,560 14 View

Is there any published or unpublished statistics on dropout rate (Dose1 to Dose-2) for Covid-19 vaccination in India, US, UK or any other country?

Are there any published or unpublished statistics or papers on the dropout rate (Dose1 to Dose-2) for Covid-19 vaccination in India, USA, UK, or any other country where vaccination has started at...

28 February 2021 4,237 1 View

Nazaruddin Sinaga Popular answer

Hi dear Parnab Saha ,

Yes, I agree with Khalid M. Saqr . In addition, please try to reduce the residual values.

Regards.

Khalid M. Saqr

You have to make sure that the error is not numerical. Check the solution sensitivity to meshing and discretization scheme (and time marching if the solver is transient). Numerical error is a very common source of inaccuracy in CFD.

Nazaruddin Sinaga