What mechanisms are in an electrochemical film formation of polyaniline to be used in supercapacitor?

01 April 2014 1 3K Report

Accessible porosity.

Faradic reactions in conducting polymers occur throughout the entire bulk. In oxidation, the ions are transferred to the polymer backbone. In reduction, the ions are released from this backbone into the electrolyte. These oxidation-reduction reactions are highly reversible.

The positively charged polymers generated by oxidation on the repeating units of polymer chains are termed as p-doped. The negatively charged polymers generated by reduction are termed as n-doped.

Badges
Science topic

More Javad Shabani's questions See All

An article on the Iranian state's civil liability in the COVID-19 matter needs supervision; Is anyone interested in collaborating?

Hello. An article on the Iranian state's civil liability in the COVID-19 issue has been written in collaboration with a friend and a comparative look at law and biology. The article is ready to be...

15 February 2021 2,906 2 View

Is it possible to report hydrodynamic loads on different parts of an ocean vehicle while 6DOF motion analysis in Ansys Fluent is running?

It seems a 6dof UDF containing vehicle characteristics such as mass and moments of inertia can be used for specifying a boundary as reprentative of ocean vehicle. It is required to have...

03 February 2021 7,726 3 View

How to determine the pH pzc (point of zero charge) for metal-organic frameworks and Organoclays?

I need to answer this question to continue my research.

12 January 2021 3,626 5 View

Do you think that our world will reach 100% of its electricity needs from clean energy sources?

02 January 2021 3,059 62 View

If you have solar PV panels and a grid-tied inverter, what happens if the system is connected to the grid without a net meter?

13 December 2020 8,874 3 View

What are the main differences between Photo Voltaic (PV) solar sources and Solar Water Heaters (SWH), especially from economical aspect?

Is it feasible to replace my Photo Voltaic (PV) solar panels system by Solar Water Heater (SWH)?

02 December 2020 4,740 7 View

Is it possible to identify of ordered phase with x-ray diffraction technique?

I want to identify ordered phases in a high entropy alloy.

11 October 2020 5,452 4 View

How is solubility of CO2 or air in organic solvents such as xylene or cyclohexane?

For some reason, I need to inject a dispersion of an organic solvent and organoclay into a block of soil sample. the organic solvent probably is xylene.

29 September 2020 6,348 4 View

I am confused about the editor's request (I had submitted a manuscript and then major revision was requested). Can anybody help me?

I had submitted a manuscript to a journal. After a while, they requested major revisions. The end of their request, they mentioned that: "You will be unable to make your revisions on the...

09 August 2020 5,436 7 View

Should Quartz powder or Sand water absorption be considered for UHPC mix design calculations? How is the water absorption of the powder calculated?

07 August 2020 1,592 1 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

fatal error

16 June 2021 0 0 View

flexibility of polymers chain

effect of double bond on the flexibility of polymers

07 April 2021 0 0 View

Formulation of polymer color flakes

I am writing to request some information for making polymer color flakes. I would appreciate the help.

17 March 2021 0 0 View

Polymer composites suddenly solidifies?

I am making polymer composite by solvent mixing method. When I am trying to add filler solution in polymer solution it quickly get solidified. How to make them then uinform? It doesn't give time...

03 March 2021 7,540 4 View

What techniques can I use to determine the miscibility of polymer blends?

The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...

03 March 2021 4,107 4 View