What is your major observation on the ratio of momentum diffusivity to thermal diffusivity?

01 January 1970 0 5K Report

Prandtl number is the ratio of momentum diffusivity to thermal diffusivity. What is/are your observation(s) on the significance of the dimensionless number on transport phenomenon?

Badges
Science topic

More Isaac Lare Animasaun's questions See All

Are you looking for an empirical review to validate your observed effects of Grashof/buoyancy parameter?

An empirical analysis is an evidence-based approach to the study and interpretation of information. Are you looking for facts to support your introduction of Boussinesq approximation and/or...

08 September 2018 8,141 2 View

Do you know any published articles in which the effects of Brownian motion of nanoparticles and/or thermophoresis parameters are presented?

Have you once reported the effects of Brownian motion and/or thermophoresis parameters on the flow of any kind of nanofluid? Or you have once studied a related report on the subject matter!!! If...

10 November 2017 595 8 View

Do you have any published article(s) in which the effect of buoyancy parameter or Grashof number is reported? Kindly drop its reference. Thanks

Such articles are needed for a meta-analysis, it would be appraised professionally and cited properly. In case you know any published article(s) as well in which the effect of Grashof number could...

05 June 2017 6,446 4 View

Why is meta-analysis of certain pertinent parameters on boundary layer flow rare to be found? Your observation or opinion would be highly appreciated.

It is worth noticing that there exist thousands of published articles on the boundary layer flow of different categories of fluids on various surfaces. However, meta-analysis of most pertinent...

05 June 2017 2,759 1 View

Request for support: Do you know how to establish the stability of the solution of ordinary differential eq (bvp) with Neumann kind of boundary?

Is there anybody with an insightful note or explanation on how to establish the stability of the solution of ODE (bvp) using Poincare-Lyapunov Theorem? Reduction of the bvp to initial values...

01 January 1970 7,078 2 View

Request for FLUENT ANSYS software

Do you have the executable (or installation) file(s) of any latest version of Fluent Ansys software? If yes, please kindly share the link to download the software with me. Thanks

01 January 1970 5,259 3 View

Which type of compound does lamda max of 218 indicate in a uv-vis spectrum of a partially purified compound through column and TLC?

A crude extract of fungal culture using EtOH was subjected to column and TLC and partially purified compound was obtained. UV vis spectrum of the compound/s has max absorbance at 218nm. The...

11 August 2024 9,801 2 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

GC-MS retention index prediticon?

Hello experts, Does anyone know any free software about retention index prediction ?

08 August 2024 7,403 2 View

Regarding LBM in Boiling?

What should be the equation for halfway bounce back boundary condition for flow field with forcing term?

08 August 2024 7,938 1 View

How to calculate CCS for Sodiated adduct ions and Multiply Charged Ions?

I'm currently working on calculating the collision cross section (CCS) for various ions, and I'm facing challenges when dealing with sodiated and multiply charged ions. Most of the resources I’ve...

08 August 2024 8,329 0 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to determine positive-stained cells in FACS? Use isotype or unstained control?

To compare positive and negative cell populations in flow cytometry, should I compare unstained cells with antibody stained cells? Or with the isotype control? Most papers show comparison with...

06 August 2024 6,728 6 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View