Which journals (Q1,Q2) accept simulation based design and results of antenna if fabrication and testing facility is not available?

I need a list of good (preferably Q1,Q2) journals that will accept research papers prepared on designs done with the help of simulation software e.g CST, HFSS etc.

08 February 2021 9,636 5 View

Proteins not stacking/ entering in a native PAGE. Can anyone help?

Hi. I am trying to study a biotin modification of my target protein in a crude cell extract and am interested to determine how much of my protein in getting biotinylated. After biotinylating my...

15 January 2021 2,214 4 View

Look for Book?

Can anybody give me the following writer book? Helen Deresky "International Management"

26 December 2020 5,109 5 View

What Electrolyte Solution should be used for EIS and CV, While material I'm using is Carbon doped Titania as a counter electrode in DSSC?

Hope so, you are all fine, I want to perform EIS and CV of my material Carbon doped Titania as a counter electrode for DSSC, I just want to know what electrolyte solution and in what molar...

25 December 2020 7,095 3 View

Look for details for the following reference for citation?

22 October 2020 9,252 4 View

Look for methodology?

Evaluating training design is similar to evaluating trainees reaction?

19 October 2020 4,575 4 View

Look for methodology?

I will do single group pre post test in evaluating training. In that case, what strategy i should follow between experimental or survey research?

03 October 2020 5,326 6 View

Can anybody give me the reference including page no of the following citation?

Mayer and Pipe (1983) suggests that the reasons for strategic plan for training evaluation is to evolve a careful methods of assessing and reporting training effectiveness, so that the...

19 September 2020 2,319 2 View

Inflection POS-suffix dataset ?

Hello, I am trying to find a dataset of canonical suffix forms for Parts of speech tags. For example, ed->VBD (past tense), ing-> VBG. Is there any available dataset like this? Thanks!

01 August 2020 5,066 2 View

Need help regarding the statistical analysis of various groups treated with various doses (single vs double)of a drug. Results are the in percentage?

There were four groups; A, B, C and D with each group containing 15 birds. All birds are of the same age. Other environmental and experimental conditions for all the groups are also same. Group A...

11 June 2020 4,834 4 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

MD MOE RMSD

How to calculate the RMSD values for a MD simulation using MOE?

07 August 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

fatal error

When I tried to energy minimization my system, I got fatal error as below. Fatal error: Atomtype opls_116 not found Although I've already added this line: ; include water #include "oplsaa.ff/spc.itp" to [molecultype] directive in my topology.

16 June 2021 0 0 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

How Can I bring as much common elements in steel as possible to calculate stable phase(s) in OpenCalphad?

As I was tweaking step-by-step OpenCalphad6 Macros step1.ocm involving phase and thermal property calculation of a High-speed steel, I could not incorporate more than 6 elements in the steel...

01 March 2021 8,840 1 View