What is the typical value of diazotroph carbon-specific growth rate?

16 November 2023 0 355 Report

Can anyone suggest the typical value of diazotroph carbon-specific growth rate at 0 degC in the global/tropical ocean, for ocean biogeochemical model?

Badges
Science topic

More Kunal Madkaiker's questions See All

What is the phytoplankton mortality rate value for the north Indian Ocean?

Can anyone suggest me the typical phytoplankton mortality rate value for the north Indian Ocean (Arabian sea and Bay of Bengal separately if possible)? Any literature that suggests this value?

10 November 2023 8,140 0 View

Conversion of plankton concentration (micro, nano, pico) from mg/m3 into mol/m3?

How can I convert plankton concentration (micro, nano, pico) from mg/m3 into mol/m3

25 September 2023 2,232 4 View

Where can I find gridded reanalysis 3D ocean DIC/TALK data?

I am looking for a gridded reanalysis 3D ocean DIC/ Alkalinity data. Can anyone suggest me where to look for?

31 May 2023 3,360 1 View

Can CO2SYS/ PyCO2SYS routine be used for a lagoon/ estuarine domain?

Are the equations used in CO2SYS/ PyCO2SYS routine applicable for lagoon/ estuarine environments where the pH levels are normally less acidic than open ocean pH?

01 May 2023 3,724 0 View

Where can I get fine resolution global river runoff/mass flux data?

I require gridded river runoff data (global). I know GFDL-ECDA provides data but it is coarser resolution (1 degree). I need finer resolution data (model/reanalysis). Kindly suggest.

14 November 2021 5,187 4 View

Regarding different nutrient limitation for small and large phytoplankton

My question is related to ocean biogeochemical modelling. How much of a difference will it make if we don't assume different growth rates and nutrient limitations for small and large...

01 January 1970 2,759 0 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

Is it necessary to covary exogenous constructs in a structural model?

I am working on a SEM model where i have 7 latent variables (6 exogenous and 1 endogenous). In AMOS when I co-vary the exogenous constructs, only 2 paths are coming significant out of 6. But when...

03 August 2024 6,028 4 View

Have you heard about Technological Surveillance on Oceanographic Research Vessels?

It is important to highlight that technological surveillance on oceanographic vessels is a collaborative effort in which different specialists work together to effectively leverage technology in...

31 July 2024 1,633 0 View