I will be appreciated if you introduce me some book and article about it.
Hi, you can use software in that work on this field, Digsilent, ...
Hi , I think the easiest way to simulate the distribution network , the software is Digsilent .
Hi. The best software is Digsilent. You can calculate every parameter that you need by this software.
I want to draw upper and lower rectangular for sin(x)dx over [-π,π] dividing the partition into 6 equal intervals. I only want the drawing and I can solve it. Best Regards,
04 May 2016 7,765 11 View
I want to analyse the optimization method of each approach. I am looking forward to hearing you,
03 April 2016 9,124 4 View
If you know some article about comparing this algorithms, I would be appreciate to tell me.
03 April 2016 302 9 View
I was reading lots of article but I can't find any good thesis.Please help me to find them.
10 November 2015 995 5 View
Why CTs are connected in star on T/F delta connected winding side & in delta on T/F star connected winding side for T/F differential protection?
09 October 2014 2,143 2 View
I want to simulate a nonlinear and differential equation with input like a linear equation using matlab simulink. I know how to solve with mfile but I want to learn using the simulink.
09 October 2014 3,220 5 View
Thanks.
09 October 2014 6,854 13 View
.
09 October 2014 570 4 View
09 October 2014 2,657 7 View
I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?
11 August 2024 3,115 1 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...
09 August 2024 7,892 0 View
I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...
09 August 2024 5,048 2 View
I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...
08 August 2024 719 0 View
My name is Apurva Saoji. I am a Ph.D scholar in Computer engineering in India. I am looking for international expert in reviewing my PhD thesis, "Competitive Optimization Techniques to Minimize...
07 August 2024 4,600 2 View
Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...
06 August 2024 9,986 2 View
I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...
05 August 2024 454 3 View
I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...
05 August 2024 3,665 0 View
Hello everyone I am looking for one or some books for propertes and behaviors of stochastic fibre orientation composites. unfotunately I could not find any suitable reference for thias by...
04 August 2024 3,461 3 View