Is there a rule to set the minimum number of Decision Making Units (DMU's) so as to get a reliable result from DEA?
For network DEA, no studies mentioned this relationship. So we can go on with the previous studies results till any update is found.
Dear Boru,
Banker et al. (1989), suggest a rough rule of thumb. Let p be the number of inputs and q be the number of outputs used in the analysis, then the sample size (n) should satisfy n >= max {p × q, 3(p + q)}.
Thank you
Take a look at the following articles;
1. https://www.academia.edu/15284036/TESTS_OF_EFFICIENCY_IN_DATA_ENVELOPMENT_ANALYSIS
2. https://www.academia.edu/30342682/Sensitivity_analysis_of_inefficient_units_in_data_envelopment_analysis
3. https://www.academia.edu/18709973/Application_of_data_envelopment_analysis_.....................
4. Article Data Envelopment Analysis in Stata
5. https://www.academia.edu/1391030/Data_Envelopment_Analysis_in_Stata
Some literature review can help in this regard.
focus areas of a phd defense limited by a 20 min allowable time
31 December 2016 7,694 4 View
a regression output might provide indication on whether variables are positively or negatively related. however, there is also a third possibility of neither of the aforesaid relationship are...
02 March 2016 3,339 10 View
Is the literature review an acceptable source of variable selection? what other sources are acceptable? thank you
01 February 2016 1,226 4 View
which one is most appropriate for quantitative dominated studies using publicly available secondary data?
01 February 2016 9,921 3 View
what technique is appropriate to conduct reliability test for secondary data (publicly available and audited data)?
05 June 2015 4,702 2 View
is the score for the entire paper or each section that would be acceptable to determine originality?
04 May 2015 8,024 2 View
how we can choose the best out of the options?
02 March 2015 7,791 6 View
any quantitative measure...
02 March 2015 5,237 4 View
Is that value adding to report all the models after the required test enabled us to choose among the three?
02 March 2015 7,615 10 View
for instance bank data which can be represented in panel and macroeconomic data which is time series?
02 March 2015 8,511 4 View
I would like to learn more about SPSS and Its application especially in regards to data analysis. Please suggest me how I can learn more about it. Thank you so much.
11 August 2024 9,101 4 View
I have reverse sequences (AB1 format), can I base on reverse DNA sequences to perform nucleotide alignment, convert nucleotides to amino acids and deposit the sequence in GenBank database?
11 August 2024 5,138 1 View
Hello, Why do i see this baseline drift when i compare my blank (black) to the sample (blue)? Any suggestions as to why this happened? Thank you!
11 August 2024 3,770 4 View
Willett, Shenoy et al. (2021) have developed a brain computer interface (BCI) that used neural signal collected from the hand area of the motor cortex (area M1) of a paralyzed patient. The...
10 August 2024 7,180 0 View
I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...
10 August 2024 4,005 2 View
I'm currently exploring the application of Python in textile engineering, specifically in areas like data analysis, process automation, and the development of smart textiles. I'm interested in...
10 August 2024 7,429 2 View
How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?
09 August 2024 7,718 0 View
Let's say we have a standard, regular hexagonal honeycomb with a 3-arm primitive unit cell (something like the figure attached; the figure is only representative and not drawn to scale). The...
07 August 2024 1,937 1 View
A fungal strain was treated with nanoparticles. We want to do an environmental SEM analysis. So could anyone share your views on preparing the sample? Thank you.
07 August 2024 5,307 1 View
Hi, I have a question about normalizing the MTT OD values for doing the statistical analysis. So, if we have 3 different plates and we call them 3 different replicates, so, first we would...
07 August 2024 8,106 4 View