How do you include resistor, inductor and capacitor in layout using l-edit? Is there any separate model file available for R,L,C?
specify a particular RLC model
90nm process technology.
Hi Raa Me,
Tutorial for L-Edit....is attached for you....
Link will be useful for you....
http://www.princeton.edu/prism/mnfl/the-tool-list/heidelberg-dwl66/LEditQuickStartGuide.pdf?__toolbar=1
Instead of checking only the mRNA level, I want to check the active protein level of MMP-1 in Liver tissue from mice. How can I do that?
03 March 2021 1,763 2 View
I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...
03 March 2021 2,297 3 View
03 March 2021 8,272 1 View
Hi. Please tell me what guidelines should i need to follow for questionaries' type research work in India. It is not hospital based work, we are conduction basic institutional based qualitative...
03 March 2021 2,037 3 View
Hi, I implemented a code to gabor filter cifar10 data but the images after being filtered and stacked are not clear like the original images. I think the problem is in the way I am using the...
03 March 2021 6,317 1 View
i am try to classify the x-ray images. During classification , can i block unwanted images (except x-ray image).
03 March 2021 7,100 1 View
03 March 2021 5,360 2 View
The term miscibility refers to the single-phase state in thermodynamics. I do not mean the compatibility of different components. To determine the miscibility I know several techniques such as...
03 March 2021 4,107 4 View
If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis
02 March 2021 7,670 3 View
02 March 2021 5,204 3 View
I'm working on Mucuna pruriens and want to quantify L-DOPA. Could someone please suggest the cheap and best solvent for the extraction and the solvent system that has to be used for its...
20 February 2021 6,058 2 View
Hi all researchers, I would like to have your practical experience in EMG-based occlusional examnation with the relevant existed commercialized systems of Gamma Dental, SAM, and the others. If...
20 January 2021 1,757 1 View
Hi all, As new DC-DC converters are being proposed, associated control method should be proposed and based on the small-model signal analysis of the DC-DC converters. Using average space state...
06 January 2021 7,247 3 View
I simulate an inductive wireless power transfer system in matlab. I set the primary and secondary mutual inductor resistance is 0.3ohm. So when i run the circuit it took high current at no load...
29 December 2020 9,536 3 View
Hi everyone, I tried to solve a frame system reinforced concrete structure in ansys. I used SOLID65 and LINK180 for this. Merge items, glue volume etc. Although I followed the commands, I could...
17 December 2020 4,472 1 View
Hello ! When tried to linearize the model for Bode plot in matlab getting the following error. In "frestimate(modelname,op,io,in)", it is required for each of the linearization input I/O...
08 December 2020 4,598 1 View
Large values of resistors and capacitors are hard to match in the fabrication phase. It will create some systematic mismatches. So how to avoid those kinds of mismatches in case of current-mode...
19 November 2020 3,709 8 View
Hi please guide me! I made the thin layer of ITO by using Pyrolysis spray method. but I can't find a way to measure its dielectric coefficient.(i need imaginary and real part of it) I have tried...
13 November 2020 1,465 7 View
09 November 2020 8,056 7 View
I cannot understand how to find the reliability of components of PV system using MIL-hbdk-217F. For example a DC link capacitor i used and how to use its parameters to find the failure rates...
26 October 2020 8,701 2 View