What is the problem with production of Inkjet Printed Schottky diode?

More Debajyoti Biswas's questions See All

How to do mono formylation of N,N-diethyl-3-methoxybenzamide?

I have attempted the formylation of the above mentioned compound using a very well reported protocol using secondary Butyl Lithium and TMEDA at - 78 degrees Celsius. I have done it quite a few...

08 February 2021 2,793 2 View

What is the minimum number of cells required for fluorescence in situ hybridization?

I have to perform a FISH experiment with limited number of cells and I am trying to estimate the minimum number of cells required to do FISH. Cells are from mammalian cell line. I failed in doing...

12 January 2021 7,887 1 View

Can you give me some Information about the generation of ROS in marine surface water?

Reactive oxygen species is a very new term i think

23 December 2020 8,416 4 View

Is the impact of Machine Learning going to last long?

Artificial Intelligence came in existence many decades ago. Then came Machine Learning algorithms. In today's world, we keep hearing about Machine Learning and Deep Web. Is the impact of Machine...

26 October 2020 6,517 7 View

How helpful will Deb Learning will be for searching?

We have built Search Engine and Page Ranking Algorithms efficiently. Even went on to design Ontology based Domain Specific Search Engine. How helpful will Deb Learning will be for searching?

26 October 2020 6,319 2 View

Can someone suggest me a wear detection method for a pipe which goes under intense heat and pressure at intervals?

I am looking for a wear detection method for a pipe that goes under intense heat and pressure for short instances at intervals. this process has an average cooldown time of 8 seconds between each...

08 October 2020 3,776 2 View

Single-cell cloning from SkBr3?

Did anyone tried single-cell cloning from SkBr3 cell line. I am failing in growing cells post single cell seeding in wells. Any help is appreciated

27 September 2020 8,762 4 View

What to do when RT PCR becomes positive again after 15-20 days of 1st sample positivity?

We are getting some patients who were initially positive of RT PCR for Covid. But in retesting after 15-20 days or even 20 days after those patients remain still positive. Is it for dead RNA...

17 August 2020 9,552 9 View

How to calculate % sequence identity using Clustal W?

I am calculating % epitope conservation for different mammalian antibodies against zebrafish. I have performed the Clustal W for antigenic peptide used in raising the antibodies against the...

05 August 2020 6,399 5 View

What is the Source of Harmonic Power ?

Consider a sinusoidal supply at fundamental frequency as shown, with a series inductive reactance leading to a bus. Let a diode rectifier load be connected to the bus. The switch Sw for resistive...

24 June 2020 8,175 27 View

What is the most Operating System (OS) which can be INSTALL on Tiny hard devices like Raspberry Pi (RPi) hardware ?

I'm targeting to deploy a mesh network and manually configure MANET routing protocols. I'm preparing scenarios, architectures, and hard devices needed to do that. Are there some step-by-step...

03 March 2021 1,931 5 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

What are anisotropic electrical and optical properties of a semiconductor due to?

In some materials, properties such as band gap, thermal conductivity differ along different crystallographic axes. What are the basics?

01 March 2021 1,923 3 View

How can I integrate a routing protocol in a tiny device (e.g. Raspberry Pi)?

Hi Community, I'm facing the issue of integration/compiling a new routing protocol in a WSN simulator. The final goal is to successfully add, configure this routing protocol in hardware devices...

01 March 2021 9,332 6 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

How to calculate battery consumption for IoT device?

Hi, everyone I'm working on a privacy-preserving algorithm that will apply to IoT devices. So, I need to measure the power consumption by implementing this algorithm. Any suggestion, advice,...

25 February 2021 8,749 6 View

What software programs can directly simulate Additive Manufacturing Directed Energy Deposition (DED)?

I understand there are a lot of software programs that can simulate DED by going through specific modeling, simulation, and commands. For me, that was time consuming and results were not accurate....

24 February 2021 4,428 3 View

How the Ground Plane implantation is performed without damaging (and w/o varying the undoped nature) the top Si (8-10 nm) in FDSOI technology ?

It is a general practice to introduce Ground Plane in FDSOI devices under the BoX. The Ground Planes are introduced by Ion Implantation through Top Si layer and Buried Oxide. I wanted to know that...

24 February 2021 5,974 4 View

How to troubleshoot Electrochromic Films and Electrochromic Devices?

I am trying to characterize an electrochromic system. The system uses ITO electrodes on glass, WO3 as the electrochromic film, and NiO as the ion storage layer. When I deposit NiO and WO3 and...

23 February 2021 9,592 2 View

Can a semi-conductor material have different absorption coefficient?

Does the absorption coefficient of the semiconductor changes with the change in the structure of the semiconductor? If you have a thin film and nanowire of the same semiconductor, will the...

23 February 2021 9,799 4 View

Maxime Harnois

So be the first to fabricate a fully printed Schottky diode. It will be a nice novel work! ;-)

Let me know if you succeed.

D. K. Dhruv

Work function of semiconductor should be higher thn metal WF for rectifying contact, the energy of the system can be reduced by holes flowing from the semiconductor to the metal, causing a depletion region.

So, care must be taken for controlled work function to get rectifying behaviour.

Roman Kubrin

Can one ink-jet print semiconductors at all?