What is the possible biological explanation of the mutational pressure as a driving force on the evolution of particular species ?

Dr Arif Uddin @Dr-Arif-Uddin

20 October 2020 1 5K Report

In one analysis major role of mutation pressure was observed in codon usage bias of some species

Mosab Nouraldein Mohammed Hamad

It may be due to various factors such as adaptation to changeable environment ,

Badges
Science topic

Similar topics
Force

More Dr Arif Uddin's questions See All

How to show arrows over the streamlines in CFD-post?

I follow this to make streamlines like the photos attached below: (software- CFD post-processing) First I plot the 2D streamline over a surface "streamline 1". them I plot a vector by the...

01 March 2021 8,668 3 View

How to increase mesh quality of a cfd model in ansys fluent?

How can one improve mesh skewness, orthogonality, aspect ratio?

28 February 2021 7,730 3 View

Specify the Burgers vectors for dislocations, which cannot be uniquely identified.?

1. A bcc metal single crystal was sliced along (1 -1 0) plane for TEM study. Assuming that the TEM available is equipped with a goniometer stage which tilts up to 45o. The Burgers vector of...

20 February 2021 2,370 1 View

Why is my CFD problem (mini heat sink rectangular channel) not converging while having good quality mesh?

My CFD problem is having two interconnected rectangular channel, which is known as mini heat sink. I have already performed parallel flow inside of an interconnected mini heat sink. However, I...

19 February 2021 3,209 3 View

How to improve dissolution of neosome?

I have made neosome from herbal drug. Neosomes are stable. But I face problems in dissolution. I used minimum ratio of 1:1:0.25 ( Drug:span 60: Cholesterol and GMs. Now how can I active better...

17 February 2021 3,584 1 View

What is the best method for preparation of Polymeric nanoparticles for co-delivery?

We are planning to make Polymeric nanoparticles for co-delivery of 2 flavanoides. Which is the best method, that one should follow.

09 February 2021 7,086 8 View

OmniScriptum Publishing Group?

Hello, Has anybody published with OmniScriptum Publishing Group. I got an email from them. The emails claims the editor is from the group but the email is signed out by lambert academic...

08 February 2021 5,611 3 View

Following is XRD of iron oxide nano material synthesised using bipyridine derivatives. What are the reasons for Broad Humps?

Even after few repetitions..I am getting similar results. Is is due to organic components?

20 January 2021 9,279 6 View

How much Ti and B (in ppm) is required for effective grain refinement and why?

To have the desired grain size in 6061 and 6063 Al alloy, what should be the minimum % of Ti and B pick up and what is the chemistry/metallurgy behind that?

07 January 2021 9,305 2 View

How to make AlV50% alloy by thermit route?

Kindly provide the technical papers/patents on the production of AlV50% alloy by thermit route, by using V2O5

05 January 2021 2,471 3 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

I got 02 moderator values defining Johnson-Neyman significance regions. Is it an error?

Hi everyone, I am conducting research for my Master's thesis. I am using PROCESS by Johnson-Neyman to analyze my Moderator model. I test the relationship between Public Service Motivation and...

03 March 2021 2,350 2 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein?

Hi In Molecular Dynamics Simulation, how do I make changes to the force field according to my protein? I got this error in the add-ion stage: Fatal error "./ amber99sb-ildn-HHH.ff / force...

01 March 2021 8,747 4 View