What is the pore-scale phase field model?

07 July 2017 1 4K Report

Pore-scale modeling is used while modeling of multiphase

flow through porous media.

This method can be used to obtain macro-scale constitutive equations, to provide multiphase flow properties for large scale models, etc.

Badges
Science topic

Similar topics
Engineering
Modeling

More Omar Rafae Alomar's questions See All

What is the main job of the associate editor?

After submit the manuscript, the paper is assigned by editor in Chief and then assigned to associate editor.

09 October 2018 1,989 0 View

What is the density-functional theory?

this method is required to evaluate the liquid–vapor density profiles for associating fluids in pores

06 July 2017 1,921 5 View

How should i model a two-phase flow in porous media by using fluent?

I m concerning with modeling a two-phase flow in porous media by using volume of fluid model.

01 January 1970 762 3 View

Why the dispersed phase method cannot be applied for the simulation of complete phase change process inside porous media?

The dispersed phase method assumes one continuous phase and one dispersed phase, where the average droplet diameter of the dispersed phase has to be specified a priori.

01 January 1970 7,142 1 View

What are the open-source softwares that can be used for modelling the complete phase change process inside porous media assuming turbulent flows?

modeling of liquid-vapour phase change process inside porous media

01 January 1970 416 5 View

What are the major phenomena that limit PV efficiency of the module

PV/T concept offers an opportunity to increase overall efficiency by making use of waste heat generated in the PV module.

01 January 1970 9,502 1 View

On what depends the photovoltaic efficiency of solar cells?

A hybrid PV/T system.

01 January 1970 6,993 4 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How does grain and grain boundary affect the ceramic when studying its dielectric properties?

I am not able to get good literature and the physics behind how first these grains and grain boundaries arises out of no where when we make a pellet to study its dielectric properties and then how...

07 August 2024 5,177 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View

What are the shear and normal stiffness values of an LLDPE liner in 3D numerical modeling of a stockpile?

I am seeking experimental or applicable data for the liner (LLDPE) interface in FLAC3D numerical modeling of a large stockpile. Could you please recommend suitable references? The preferred data...

05 August 2024 3,665 0 View

How Social Media Affects Your Mental Health ?

How Social Media Affects Your Mental Health

04 August 2024 6,961 3 View