Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Sample dilution for quantitative analysis using ELISA?

If the detection range is in ng/ml but the reference range is in ug/ml for a molecule or protein in serum or plasma .how to dilute and what is the initial volume to be taken for quantitative analysis

02 March 2021 7,670 3 View

What are the new 2D nanomaterials were used for Silver nanoparticles stabilization?

In the stabilization of AgNPs are vital in current research interest. However, some of the 2D nano-materials like graphene oxide, MoS2, etc... previously used to stabilize it. But still they shown...

01 March 2021 2,207 3 View

How can we raise the figure when we writing a paper with Latex ?

Hi, everyone. I'm a starter to write a paper by Latex. But I have some difficulty using it. I'm writing the paper with 2 columns. And, there is one figure that occupies the 2 both-sides. I want to...

26 February 2021 3,738 3 View

What information can be had from raman at higher wavenumber?

i have recorded raman spectra of strontium oxide thin film. the spectra were recorded in the range 400 to 4000 cm-1. i have reference to peaks upto 1000cm-1. but i couldn't find literature for...

26 February 2021 2,499 1 View

What are the methods used for CNT..?

Respected Professor's i hope you are doing well and happy. i need some information about carbon Nanotubes. before blending the CNT with the matrix the CNT has been introducing in some treatments....

24 February 2021 5,383 5 View

Satellite orbit estimation using Recurrent Neural Network - what should I use?

Hello, I am a master's student studying in Yonsei Univeristy, Korea. I am trying to estimate the state of satellite, using Neural Network. Below is a simple flow of my study. 1. Train (t0 ~ t1)...

23 February 2021 6,383 3 View

Langevin Dynamics in shear flow?

Hi, We are trying to simulate particles with Langevin dynamics in a shear flow by Lees-Edwards boundary conditions in MD simulations. It seems thermal forces and shear flow do not go hand in...

23 February 2021 1,761 1 View

What is the system of units used in the thermal conductivity by Spitzer and Harm?

23 February 2021 9,253 1 View

How we can measure Kemp % in wool without using of benzene?

Would you please let me to know about the methods for measurement of medullation and Kemp % on animal? My problem is that the wool sampling and sending to laboratory is not possible. So I would...

21 February 2021 7,260 4 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Which fluorescent dye to use for measuring total ROS production?

Is DCFDA appropriate for measuring total ROS production, or can it only detect certain types of ROS? If I want to measure total ROS production, which dye should I use?

01 March 2021 9,447 3 View

Why do the air flow results vary totally when adding scalar in CFD ?

Dear All, We are using Autodesk cfd to calculate the air flow in a single sided naturally ventilated room, where air flow depends only on buoyancy due to temperature difference between inside and...

25 February 2021 9,602 4 View

Is is possible to pole with corona poling pellets of the sample material instead of thin films?

As it is highly probable that pellets will have a higher degree of air gaps and voids than thin films, is it possible to pole the samples with corona poling nevertheless? Or is there the...

24 February 2021 1,349 1 View

Have you ever experiencing air vent trouble in fermentation process?

Dear all, My research group is currently working with a 12-litre fermenter. Somehow, if we do the fermentation for more than 20 hours, the process will be more prone to contamination. Our current...

23 February 2021 1,908 2 View

Help with assigning pressure boundary conditions in FLUENT on a large structure?

Hello, I created a very tall tower (>1000m) and applied pressure boundary conditions at the inlet (bottom) and outlet (top) that correspond to the pressure are their relative altitudes....

22 February 2021 9,972 4 View

What type of pressure sensor are usually used in microfluidics?

My team is designing a dual channel microfluidic chip that runs air and water. I think we've decided on the NE1000 syringe pump for it's versatility and feedback control. We will be ordering the...

18 February 2021 9,928 2 View

Not able to charge-discharge Li-ion coin cell at higher C rate ?

I am working on cathode material. I have made different Li-ion coin cell against Li metal using commercial available cathode materials such as LCO,LMO, LFP and NMC and also with the lab...

18 February 2021 1,450 3 View

How to find the air side pressure drop in a spiral fin tube bundle cross flow heat exchanger?

How to find the air side pressure drop in a spiral fin cross flow heat exchanger? The pressure difference at the inlet and outlet is very low compared to the experimental results, which I...

18 February 2021 1,109 2 View

Is it correct to identify an air mouvement by the Venturi effect in buildings ?

Knowing that the Venturi effect is used most in tubes (according to my basic knowledge in physics) to increase the speed of air or liquids by reducing the tube volume, my question is if we have...

17 February 2021 1,260 1 View