What is the minimum number of cells required for fluorescence in situ hybridization?

13 January 2021 1 8K Report

I have to perform a FISH experiment with limited number of cells and I am trying to estimate the minimum number of cells required to do FISH. Cells are from mammalian cell line. I failed in doing it from a 96 well plate. Can someone help?

Md. Kabir Ahamed

Hi Antara Biswas,

These might be helpful for your research query:

Book Comprehensive Cytopathology

Article Fluorescence in situ hybridization (FISH) and cell sorting o...

Chapter Fluorescence In Situ Hybridization of Cells, Chromosomes, an...

Best wishes. Stay safe and warm.

Badges
Science topic

More Antara Biswas's questions See All

How to do mono formylation of N,N-diethyl-3-methoxybenzamide?

I have attempted the formylation of the above mentioned compound using a very well reported protocol using secondary Butyl Lithium and TMEDA at - 78 degrees Celsius. I have done it quite a few...

08 February 2021 2,793 2 View

Can you give me some Information about the generation of ROS in marine surface water?

Reactive oxygen species is a very new term i think

23 December 2020 8,416 4 View

Can someone suggest me a wear detection method for a pipe which goes under intense heat and pressure at intervals?

I am looking for a wear detection method for a pipe that goes under intense heat and pressure for short instances at intervals. this process has an average cooldown time of 8 seconds between each...

08 October 2020 3,776 2 View

Single-cell cloning from SkBr3?

Did anyone tried single-cell cloning from SkBr3 cell line. I am failing in growing cells post single cell seeding in wells. Any help is appreciated

27 September 2020 8,762 4 View

What to do when RT PCR becomes positive again after 15-20 days of 1st sample positivity?

We are getting some patients who were initially positive of RT PCR for Covid. But in retesting after 15-20 days or even 20 days after those patients remain still positive. Is it for dead RNA...

17 August 2020 9,552 9 View

How to calculate % sequence identity using Clustal W?

I am calculating % epitope conservation for different mammalian antibodies against zebrafish. I have performed the Clustal W for antigenic peptide used in raising the antibodies against the...

05 August 2020 6,399 5 View

What is the Source of Harmonic Power ?

Consider a sinusoidal supply at fundamental frequency as shown, with a series inductive reactance leading to a bus. Let a diode rectifier load be connected to the bus. The switch Sw for resistive...

24 June 2020 8,175 27 View

What is the best book on Game theory from the perspective of Computer Science and Engineering?

I do not know much about game theory. I am finding a book where different protocols and algorithms of computer science have been analyzed using the concept of game theory.

17 May 2020 4,774 7 View

How can a PhD in interdisciplinary fields can benefit a researcher in job market?

I am a PhD scholar of Humanities and my research is broadly connected to Anthropological studies and framework. I have also published with an Anthropological journal of global repute and looking...

10 May 2020 4,202 1 View

What are the possible parameters that can be used to detect the infected people with CoVID 19 in a person's vicinity?

Currently, few research institutes and universities are working on this problem of detecting people affected with CoVID 19 in the vicinity using voice recognition models. But are there any...

30 April 2020 7,694 15 View

Binary Logistic Generalized Linear Mixed model in SPSS. Is it doable?

I want to analyses the proportion of swimming sperm of three species of fish in two salinities. To analyse the proportion of swimming sperm in a Generalized Linear Model, I would use a Binary...

03 March 2021 2,297 3 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Waters 2707 HPLC autosampler problem?

I am using a 2707 waters HPLC device. When I try to inject a sample, it says missing plate or rack. I changed the needle and calibrated its position but I still get the same problem. I even get...

02 March 2021 1,408 1 View

Should we change media after1st 6hrs after plating HUVEC bought from INVITROGEN?it's not recomended by invitrogen.Will DMSO present in stock matter?

We have HUVEC bought from Invitrogen. Cat no -C-003-5c. while first plating the cells we have bought the protocol suggests not to centrifuge the cell with media to remove the DMSO. Should we...

02 March 2021 3,713 2 View

How to normalise data on OPM package from R Studio ?

Good afternoon, I recently used OmniLog from BIOLOG for my experimentations : I tested the metabolism of different strains on 2 types of plates. I have 16 strains of 3 different groups...

02 March 2021 3,584 1 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

How to accurately quantify chitin?

Hi all, I have been working on the quantification of chitin in insect samples and feed for a while but I can notice that the quantification methods (e.g. exposure to HCl, NaOH, and weighing sample...

01 March 2021 1,843 2 View

Can someone suggest a way to prepare slides to observe under confocal microscope for observing fluorescent tagged proteins??

I am growing the cells on coverslips and transfecting the fluorescent tagged protein directly on them. Then i want to observe these cells under confocal microscope. Currently i am just using...

01 March 2021 6,142 3 View

How to define tie constraint between rigid body and another part in dynamic explicit model of Abaqus?

Hi dear researchers I connected a rigid body into the part of my structure by tie constraint and then I added displacement to rigid body, in static general step every thing is fine and these two...

28 February 2021 3,442 2 View

Good morning research fellows, Has anyone worked with senna alata plant extract on any kind of fish?

Literatures on the piscicidal effect of sennaa alata is scanty. if you have any related litrature either in the bark, leaves or roots used as treatment to any aquatic organism please kindly help...

28 February 2021 9,138 2 View