What is the mechanical strength of flash in hot forging dies?

31 March 2015 0 2K Report

Someone knows which is the relation between the mechanical strength of flash in hot forging dies and the type of forging steel, the forging temperature, the internal pressure die, the flash shape and dimensions?

Badges
Science topic

More Daniel Martinez Krahmer's questions See All

How can I use the cif data obtained from rietveld refinement extracted via gsas2, for microstructural analysis using ETEX software?

09 August 2024 7,718 0 View

H-index issues?

Hi Sir/Madam, I would like to know why my h-index is stuck to 15 despite the number of new publications added. Could you explain me how marks are granted. Best, Daniel

28 July 2024 2,607 2 View

I'm looking for a tool to evaluate the risk of bias in... Are there any recommended applications or platforms?

Dear researchers, In a systematic review (not a meta-analysis) compiling studies on various diagnostic systems against a specific pathogen. The most relevant parameters evaluated are the type of...

03 July 2024 9,069 3 View

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visit?

What is the current usage and patronage of parks and greenspaces by older adults (aged 65+) in Salford? How does the frequency of older adults' visits to parks and greenspaces in Salford relate to...

22 June 2024 7,616 1 View

How can we compare SENTINEL vs LANDSAT for NDVI?

A question to see who can answer it. If the red and infrared bands of the satellites are...

16 June 2024 2,249 1 View

ImageJ Concentric Circles?

Hi there! We are trying to use the Concentric Circles Plugin on ImageJ to determine signal intensity in neurosphere cryosections after immunocytochemistry/confocal analysis. We determined the...

12 June 2024 7,332 0 View

How do i use researchgate to cunduct literature review ?

I am a first-time researcher in the field of nursing and i would like to conduct research about knowledge and attitude towards prevention and spread of tuberculosis.

11 June 2024 3,821 2 View

Is there any possibility for cultured mouse neurons more than 7 days?

Dear colleagues, I'm planning to start neuron mouse co-culture with astrocyte and microglia but I heard that it's difficult to keep it up. Any advices?

27 May 2024 4,905 3 View

What are some possible technical failures during lentiviral packaging using HEK293T?

I'm having trouble packaging lentivirus in HEK293T using pCMV, pMDG, an shRNA and polyfect. I normally seed 1.5 x 106 HEK293T cells in 60 mm on Day 0, which translates to about 60 to 70%...

20 May 2024 9,067 1 View

What is the minimum amount of liquid and beads I can use for bead-beating in a 2ml vial?

I am planning to extract DNA with QIAamp Mini DNA extraction kit (Qiagen) from DNA Shield microbiome preserved samples. My samples contain small amount of cell, so my goal is to reduce the loss of...

14 May 2024 2,291 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Simulation of metal drawing by Abaqus with UMAT?

Hello, colleagues. Recently, I have been working on a metal processing simulation with my UMAT in Abaqus. I have outlined the corresponding simulation, but I keep encountering issues that cause...

30 July 2024 7,062 1 View

How to make the concentration measurements for the hydrogen absorption/desorption in the metal hydride?

Hello Everyone! I am trying to create a metal hydride system where I am trying to create a temperature control with the emphasis on measuring the concentration of the hydrogen with the hydrogen...

29 July 2024 7,577 2 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

How can biogenic synthesis techniques be applied to develop plants capable of extracting and processing heavy metals from contaminated soil, and wha?

Understand how to utilize biosynthesis to develop natural and sustainable solutions to address heavy metal pollution and improve environmental and agricultural conditions.

26 July 2024 1,469 1 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

What is the main used curing agent for epoxy based coating?

I am trying to coating metal oxide into steel substrate, for better sticking planning to utilse epoxy based, Could you please suggest suitable curing agent for the coating purpose

25 July 2024 438 3 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View