What is the latest trend in predicting/simulating performace of Solar PV performance?

Vijaykumar Ramalingam @Vijaykumar_Ramalingam

06 June 2013 0 7K Report

Solar PV Performace is affected by various factors such as temperature of cell, irradiation, dust etc. Many methodologies are developed numerically and measured. What are the latest trends in this area of research?

Badges
Science topic

Similar topics
Engineering
Modeling

More Vijaykumar Ramalingam's questions See All

What are the forecasting models avilable for Solar PV performance?

I am trying to predict the future performance of Solar PV (hourly and daily) basis. What are the statistical models available? Any pointers towards the same would be appreciated. Thanks

05 June 2016 7,701 0 View

How can we split the Excel file containing Solar PV data (for months) into small files of daily data, as excel file has the limitation on rows?

In order to analyze daily yield of Solar PV , the master file needs to be split into smaller files. As Excel has limitation of number of rows, it is tough to load or extract the same. Hope there...

31 December 2014 9,015 5 View

Has anyone performed a thermal analysis on temperature profiles on photovoltaic modules based on irradiation?

This is to study the effect of temperature on Solar Cell Performance.

07 August 2012 2,683 8 View

Could you recommend some articles on Urban Transportation System optimization and Innovation?

13 August 2024 2,595 3 View

How can I prepare virus for a TEM or SEM imaging?

I have virus (viral hemorrhagic septicemia virus) in suspension and the experiment will not involve cells. What level of TCID50 is preferred?

11 August 2024 3,115 1 View

Can you connect an HPLC to a Mass Spec only at a certain time point?

Can anyone explain this method? Especially the last statement where it says only at 1.5 to 2.5mins was the MS/MS connected to the UPLC. How is that possible, is it a feature in this specific...

11 August 2024 8,141 3 View

Handling Missing Data and Building a Predictive Model with Incomplete Information ?

I am developing a predictive model for a water supply network that involves 20 influencing points. However, I only have historical data for 10 out of these 20 points. I would like to know how to...

10 August 2024 4,005 2 View

Is it possible to use the Fused Deposition Modeling (FDM) to additively manufacture interconnected porous structure generation of >100-200 micrometer?

Usually, additive manufacturing techniques like SEBM, SLS, and SLM are used for interconnected porous lattice structure generation with sizes of >100–200 micrometers. Can the Fused Deposition...

09 August 2024 7,892 0 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

Separation of organic acids-HPLC?

Hello What should be done to separate and identify organic acids in HPC when their RetTime is the same?Like oxalic acid with Propanoic Acid.or acids that have a very close RetTime.

07 August 2024 8,782 3 View

Can you suggest reliable sources defining "3D mesh" and "3D city models"?

Dear fellow researchers, I am currently working on a paper where I need to provide a reliable reference that defines and distinguishes between 3D mesh models and 3D city models. Although I am...

06 August 2024 9,986 2 View

Please explain how the plastic input value should be considered from the true stress-strain curve for the bilinear elastoplastic material model ?

I am working on Abaqus/Explicit(Quasistatic ) for the deformation of the auxetic structure model. Please explain how the plastic input value should be considered from the true stress-strain curve...

05 August 2024 454 3 View