21 June 2018 3 655 Report

I am planning to optimize the drying process in a washer dryer combo

More Pramodvishnu Pramod's questions See All
Hello Researchers, Can anyone guide me on estimating the Leaf Area Index (LAI) of wheat using only weather and soil parameters? Is it possible?

I need to estimate the LAI of a wheat crop using only weather and soil parameters. Can anyone please help me?

28 July 2024 4,886 2 View

Can we measure the 2θ variation within a 5° range on a Bruker D2 Phasor XRD? is it compatible with diffraction angles (2θ) below 10°?

Can we measure the 2θ variation within a 5-degree range on a Bruker D2 Phaser XRD machine? I have experienced problems with diffraction angles (2θ) below 10 degrees. Is this range within the...

13 July 2024 2,615 4 View

To model Carbon quantum dots(CQDs), which CIF file should be selected?

I have doubts about which CIF file should be selected to design the carbon quantum dots. Any help or suggestions would be greatly appreciated. Thank you very much for your assistance.

19 June 2024 7,541 1 View

How to perform the DFT calculation on the mechanism of Photocatalytic CO2 reduction with water?

Dear Researchers, I hope this email finds you well. I am currently working on research involving DFT calculations to study the mechanism of CO2 reduction using a catalyst with water as the...

14 June 2024 4,612 4 View

Why and how the electrochemical response of boron-doped diamond (BDD) electrodes is not stable over time in ferro-ferri redox mediator electrolyte?

I am trying to utilize boron-doped diamond electrodes for developing electrochemical biosensors. During the electrochemical measurements, it was observed that the current response varies with...

10 June 2024 6,311 1 View

How to convert unit eV to V of the valence and conduction band position of semiconductor?

This question asks for a detailed explanation of the conversion process between these units in the context of semiconductors.

22 May 2024 1,892 1 View

LR reaction producing colonies without my Insert. What could be the issue?

I am trying to clone the cowpea gene (3.5Kb) under the control of the 35s promoter (Gateway plasmid pK7WG2D). I used pDONR222 for the BP reaction. I got the positive colonies, and then sequencing...

01 May 2024 8,489 2 View

Can Metabolic Disorders cure by medicine,sustitutes,gens,and stemcell excercises etc?

Metabolic disorders occur due to our proper habits of eating process and remineralisation in the mouth. Like food, water, and liquids, etc. Due to mutations in all our food in saliva, the...

22 April 2024 1,959 3 View

What temperature is needed to eliminate carbon from the catalyst through calcination?

I have to calculate the carbon content present in the catalyst from the TGA plot. Does anybody have an idea?

17 April 2024 4,718 2 View

What are the issues in the learning of English vocabulary as a second language learner?

Issues in the vocabulary, Problems, or obstacles. Learner learn English as a second language. Learners are High school students faces difficulties in acquiring sufficient vocab.

09 April 2024 5,199 3 View

Similar questions and discussions
How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

How to heat polymer for about 130° without oil bath ?

is there any other way to heat a polymer evenly other than oil bath if so what are those and how to use it

06 August 2024 947 1 View

What should I do with parameters that are not relate to my simulation in MyLake model?

I want to Estimate surface heat fluxes using MyLake, but I don't have all the initial values in model parameters section and other sections,is there a way?

04 August 2024 1,537 1 View

Is the black sediment consider as sand? If not, how can I filter it out?

Hi researchers! I'm working on soil texture analysis, and the end result for sand is doubtful because there is black sediment appearing after drying, as shown in the figure. Is it considered sand?...

30 July 2024 557 2 View

Where to start the Analytical model for Dry sliding wear of metal surface ?

I am doing research on wear mechanism of the additive manufactured metal parts under dry condition. Please share the reference to start the analytical modelling of the wear prediction.

29 July 2024 6,115 0 View

What are the perfect mathematical model for a solar-powered ship implementation?

A computational study of heat flux on cylindrical surfaces using CNT hybrid nanofluids

28 July 2024 4,985 1 View

Seeking recommendations for equipment to mimic sunlight and heat up a greenhouse system?m?

I would like to conduct artificial sunlight experiments to mimic heat capture and air warming in a greenhouse system. The main objective is to heat up the temperature inside the greenhouse, not...

28 July 2024 4,006 2 View

Can anyone kindly suggest research topics in the area of thermodynamics, heat transfer, fluid mechanics or renewable energy?

I am an undergraduate mechanical engineering student seeking suggestions on topics related to either thermodynamics, fluid mechanics, heat transfer or renewable energy for my final year project....

24 July 2024 4,058 5 View

Issues with Malaria Coated Nitrocellulose Membrane Releasing Moisture?

Hello, I am currently working with Malaria Pf/Pan nitrocellulose membranes coated for malaria detection. After drying the coated membranes in an Incubator (overnight at 37°C), I've noticed that...

16 July 2024 7,937 1 View

Our partners will collect data and use cookies for ad personalization and measurement. Learn how we and our ad partner Google, collect and use data. Agree & close