What is the homogenization temperature for AA7075-T7351 alloy?

More Purnashis Chakraborty's questions See All

Are the yield strength of compression test and tensile test same for AA-7075?

I am doing quasi static and high strain rate compression and tension test but the yield value are different. Compression yield is grater than tensile yield. What is the reason behind it.

07 August 2018 10,081 17 View

Why fracture strain for metals (Aluminum, Mild Steel) in pure share is higher than pure tension?

We are studying the effect of combine (Shear and tension) loading on failure of Metallic structure (Aluminum and mild Steel). We observed that failure strain in Pure shear is higher than the Pure...

02 March 2018 5,408 13 View

Why does Fracture Strain and Fracture Toughness increases with increase in strain rate, for aluminum alloys ?

Dear all researchers, I observed that Fracture Strain and Fracture Toughness of Aluminum Alloys depends upon the strain rate, as we increase the stain rate Fracture Strain and Fracture Toughness...

31 December 2017 1,147 17 View

How to evaluate Johnson-Cook material constant (A,B,n,C,m) from a true stress vs true strain data?

I have some experimental data from tension tests,compression tests on a material and need to formulate a model using Johnson cook's approach (paper: "A Constitutive model and data for metals...

01 February 2017 9,268 3 View

Why does flow stress increases with increase in strain rate?

I know that at low strain rates the flow stress increases with increase instrain rate. At higher strain rates it still increases but at a slower rate because of the softening effect due to...

08 September 2016 8,056 8 View

Which Scopus Journal provides the most affordable fees?

"PUBLISHING IN A SCOPUS JOURNAL" Researchers are now at a cross road. The critical need to publish in a Scopus or ISI, etc journal is ever vital. Journal Publication fees must be submitted....

10 August 2024 8,621 1 View

Geotechnical Engineering (Proceedings of the ICE) time review?

Hello everyone, I recently submitted an article to Geotechnical Engineering (Proceedings of the ICE), and the current status has been listed as "EiC Pre-assessment: Ready" for the past 20 days. I...

10 August 2024 6,493 1 View

Seeking Advice on Viability and Execution of Undergraduate Thesis Topic?

Hello everyone, I am currently developing a thesis proposal and would appreciate your input on its viability and how to effectively carry it out. My proposed topic is: "Does the perceived threat...

10 August 2024 8,992 0 View

I have get this error when i calculated the geometrical optimization for prco3, it takes 12 hours until gives this message in the outputfile?

Fatal error in MPI_Allreduce: Other MPI error, error stack: MPI_Allreduce(1628)......: MPI_Allreduce(sbuf=000002459254A180, rbuf=000002459F86A140, count=4851, MPI_DOUBLE_COMPLEX, MPI_SUM,...

09 August 2024 7,615 1 View

How to define an anisotropic material with asymmetric elastic compliance/stiffness matrix in ANSYS APDL?

I need to model an anisotropic material in which the Poisson's ratio ν_12 ≠ ν_21 and so on. Therefore, the elastic compliance matrix wouldn't be a symmetric one. In ANSYS APDL, for TB,ANEL...

09 August 2024 5,048 2 View

Who will be moral responsible for the death of thousands of people in the event of an earthquake?

Who will bear moral responsibility for the deaths of thousands of people in the event of an earthquake? Weeks and months remain before the onset of strong earthquakes that bring death to...

08 August 2024 6,134 12 View

Is there anyone with experience in TEM analysis who can assist with a manuscript for an upcoming journal?

Hello dear colleagues, We have prepared a manuscript on NiTi-based alloys and are seeking a second opinion on our current TEM results. If you are a Ph.D. holder with experience in TEM and have...

07 August 2024 9,563 0 View

Hello Everyone ! I'm looking for a good journal to publish my manuscript with low publication cost?

I am Looking for a Science Journal with good impact factor and low publication cost to publish a review paper. Your suggestions would be appreciated.

06 August 2024 6,796 3 View

Why does my protein refolded to beta sheet during thermal denaturation analysis?

Hi! So i attempted to understand a novel protein behavior towards heat application by analyzing its secondary structure change. I subjected the protein to a thermal denaturation analysis using...

06 August 2024 1,989 3 View

What is the prepared reference material that can be used in inductively coupled plasma optical emission spectrometry (ICP-OES) to measure REE and U ?

What is the prepared reference material that can be used in the ICPE-9820 Shimadzu Japan instrument, which employs inductively coupled plasma optical emission spectrometry (ICP-OES) to measure...

06 August 2024 1,896 1 View

Gedvidas Bikulcius

Dear Purnashis,

Temperatures homogenization of aluminium alloys see in:

https://link.springer.com/chapter/10.1007%2F978-1-4757-3001-2_5

Best regards,

Gedvidas