What is the field behavior in Mode 1 of attached design?

More Anveshkumar Nella's questions See All

Do you think can be any Uranium bearing rocks in Eastern part of Iran and western part of Afghanistan?

I want to know more about Uranium ore deposits in world.

11 August 2024 6,720 0 View

Do you think can be any diamond bearing rocks in Eastern part of Iran and western part of Afghanistan?

I want to know more about diamond ore deposits in world.

11 August 2024 2,167 1 View

What is the difference between mathematical R^4 space and physical 4D unit space?

We assume that the difference is huge and that it is not possible to compare the two spaces. The R^4 mathematical space considers time as an external controller and the space itself is immobile in...

10 August 2024 6,678 14 View

If Banks do not provide credit facility, what are the options available for FPOs and impact on producer’s income?

10 August 2024 8,198 5 View

Controlling for pupil light reflex when analyzing pupil size time course?

I used eye tracking to examine how participants from two different populations (A and B) react to an image. Participants in population A exhibit larger pupil sizes over time, but they also have...

10 August 2024 3,229 0 View

What are a “Farmers Producer Organization” (FPO) and its essential features?

10 August 2024 477 5 View

Strugglling with m6A dot blot any suugesstion ?

I have been doing the m6A dot blot for a while with no improvement, I am extracting the RNA, and I can see the dots although the three biological replicas give a different reading on the memberan...

10 August 2024 8,539 5 View

Do interactions between biosphere, carbon cycle, & water cycle impact global warming & interaction between atmosphere & hydrosphere?

How do interactions between the biosphere, the carbon cycle, and the water cycle impact global warming and interaction between the atmosphere and the hydrosphere?

09 August 2024 3,291 2 View

How to get moment output in Abaqus Standart?

I have input a moment load in module load Abaqus, i put my moment load on the node surface (using reference point). I have define moment in history output and make a set for moment too. But the...

08 August 2024 4,831 4 View

How is energy cycled through the Earth's climate system and how do matter cycle and energy flow through the rock cycle?

08 August 2024 8,162 0 View

I can't see the ssDNA band after performing asymmetric PCR. Is there any way to do this?

After performing symmetric PCR, PCR purification was performed. Afterwards, asymmetric PCR was performed using the PCR purification product as a template, but no ssDNA band was confirmed in the...

08 August 2024 1,668 3 View

Can't spin-orbit coupling(SOC) be included in optical properties calculation in CASTEP?

I am currently using CASTEP version 2020. When I want to run optical properties calculations with spin-orbit coupling(SOC), I encounter the following error in a pop-up window before the job gets...

02 August 2024 2,890 0 View

How to calculate effect size of AMCE (Average Marginal Component Effect) in Randomized Conjoint Experiment?

I am following Hainmueller, Hopkins, and Yamamoto's (2014) paper for my randomized conjoint experimental data analysis. The link to the paper is provided below. I received a comment from the...

02 August 2024 4,406 0 View

Why Powder XRD is performed after cruhsing a crystal if Single Crystal XRD analysis of the same crystal has been performed already ?

What information we can get from PXRD analysis other than from SCXRD analysis of a crystal ?

30 July 2024 6,261 4 View

Can I proceed with Response Surface Methodology (RSM) with only one factor for further optimization?

I went for Plackett Burman Design for selecting the optimization factors of growth conditions for pesticide degradation. I started with 7 parameters. But, after the experiments and analysis, only...

29 July 2024 5,015 1 View

How to know the b axis of a single crystal?

How to apply magnetic field parallel to b axis of any crystal

29 July 2024 4,083 2 View

I did hirshfeld surface analysis for molecule but did not find red spot and interaction surface in energy frame work, is it ok for research article ?

In hirshfeld surface calculation i did not find any red spot in hirshfeld surface, is it ok for research article to write?

28 July 2024 2,988 0 View

How to conduct a sensitivity power analysis for Kendall's Tau?

Is there a straightforward way to conduct a sensitivity power analysis for a Kendall's Tau correlation? I was considering using the sensitivity setting and "Correlation: point biserial model" test...

28 July 2024 6,133 8 View

Why specific capacitance is not proportional with the specific surface area?

Dear researchers, Why specific capacitance is not proportional to the specific surface area? I have material A with a surface area higher than material B, but material B is showing little bit...

26 July 2024 9,156 2 View

Can anyone help me explain my problem?

Hi, Now I am doing a single-base editing by using HiFi Cas 9, guideRNA, single stranded DNA, HDR Enhancer V2 and my tranfection mehtod is lipofection (RNAiMax). Unfortunately, after gene editing,...

26 July 2024 2,136 0 View

Azita Goudarzi

hi dear.your antenna is broadband? in frequency band from 6-8, it is broadside but in the others i cant see.can i know your analysis about the mode 2 to 5? how does you explain the behavior?

thank you

Anveshkumar Nella

Dear Azita,

It is broadband..... In different modes from 2 to 5 I am getting the TE and TM modes...

Saka Harshavardhan

HI anvesh, Hope the below plot helps you to understand the first mode. The first mode is Quasi-TEM mode. Depending on the size of the wave port different modes will be excited. In order to understand mode number u can view the field modes in port option.