What is the effect of cutting speed on chip thickness? Whether chip thickness increases with increase in speed or it is inversely proportional?

Shrikant スリカンタ U. ウ. Gunjal グンザル @Shrikant_surikanta_Gunjal_gunzaru

11 November 2016 0 8K Report

What is the effect of increase in cutting speed on tool life, surface roughness and chip thickness? Any specific opinion for turning of steel for above stated question?

Badges
Science topic

More Shrikant スリカンタ U. ウ. Gunjal グンザル's questions See All

Need help :dear all, can you please suggest project ideas / title related to seismic analysis for ME(PG) Structure(civil)engineering project?

Dear all,Please suggest me some project ideas/Title related to seismic analysis for ME (PG) Structure(civil )engineering final year project,for my wife. kindly suggest recent ,innovative ideas...

08 September 2017 6,781 2 View

Need guidance regarding Taylors Tool life equation. Where will I get values of n & C for different cuting environments?

Details are as follows- W/P material- AISI 4340 hardened steel Cutting inserts- AlTiN coated carbides Cutting environment- (a) MQL with 1) Canola 2) Coconut 3) Soyabean & 4) Synthetic oil and...

10 November 2016 498 5 View

How can I apply boundary conditions in an orthotropic steel deck numerical model using ABAQUS software?

I am trying to simulate vehicular loading on an orthotopic steel deck bridge section in ABAQUS software. The red arrow mark in the attached figure indicates the direction in which the vehicle will...

08 August 2024 719 0 View

How to fix errors in my heat transfer steel structure with reinforced concrete slab model Abaqus?

I have modelled a steel structure using beam elements in Abaqus and attached to this structure reinforced concrete slab. The analysis that I am making is heat transfer of the structure. The...

07 August 2024 1,028 0 View

What should be the sample container for the hydrothermal reaction in a microwave reactor at 180 °C for 10 min at the heating rate of 5 °C per minute?

Suggest one of them 1. Teflon-lined stainless steel autoclave: 2. Alumina (Al2O3) ceramic container

30 July 2024 7,326 1 View

Should the amount of DNA input used for ChIP-seq library preparation be matched between the control and experimental groups?

Hi all. As a beginner in ChIP-seq experiments, I hope you understand that the following questions might be somewhat basic. I am planning to perform ChIP-seq or MeDIP-seq analysis to investigate...

28 July 2024 6,938 1 View

Will the catalytic effect of retained austenite happens in steels including RA?

The catalytic effect of retained austenite refers to the phenomenon wherein quenching steels with a small amount of retained austenite, when subjected to tempering at a specific temperature...

27 July 2024 8,508 0 View

Please investigate the effect of temperature and strain rate of hot deformation and the formation of delta ferrite in martensitic stainless steel 410?

25 July 2024 9,408 0 View

How to saturate steel samples with hydrogen?

I have tried to saturate ferritic steel with hydrogen using the electrolytic method and H2SO4. However, the effect was very poor even after 3 days of "saturation". Can anybody help in choosing a...

24 July 2024 4,393 2 View

Promotor observation in region annotation of RNA RIP-seq?

Hello all, I extracted RNA from my samples and performed RIP-seq. After annotating the genomic regions using R, I obtained promoters, exons, introns, and UTRs. Given that my samples consist of...

18 July 2024 1,579 2 View

Masonry Interaction Module ABAQUS?

I am simulating interlocking / dry stacked masonry in Abaqus. I am using a friction coefficient of 0.6 for my model as it is stated in the previous research as well as in the base paper. The...

16 July 2024 5,047 0 View

How to cacualte the creep life of polycrystal with CPFEM?

I saw a paper(PHAN V-T, ZHANG X, LI Y, et al. Microscale modeling of creep deformation and rupture in Nickel-based superalloy IN 617 at high temperature [J]. Mechanics of Materials, 2017, 114:...

16 July 2024 8,436 0 View