How do I measure the splitting ratio of proton exchanged Y-junction waveguide?

29 March 2017 1,969 5 View

How can i model negative corona discharge for a wire-to-plane geometry?

Dear all, I would like to study negative corona discharge for poling non linear optical crystals e.g Lithium Tantalate. I have however attempted to use plasma model example in COMSOL but i don't...

23 September 2016 4,512 3 View

How do I design a Y-junction using comsol multiphysics or matlab?

Y-branch waveguide structures are fundamental elements of integrated optics devices such as power or optical splitters, power or optical combiners, integrated-optic gyroscopes, Mach-Zehnder...

03 January 2016 8,718 4 View

Why Austenite grains in steel show much more twinning than ferrite grains?

It is oftentimes said to be a distinctive metallographic trait that differentiates a fully austenitic and a fully felly ferritic steel without etching that might distinguish between two. Why...

02 March 2021 728 2 View

How to replicate the well conditions of a crystal hit with 20%(w/v) isopropanol?

I had a crystal hit in a well with 0.1M HEPEs pH 7.5, 10%(w/v) PEG 4000, and 20%(w/v) isopropanol. Why is isopropanol in w/v here if it's just solvent? How do I recreate this well condition?

25 February 2021 9,761 1 View

Can we recognize signs of the "volatility clustering" property of a time series in its time domain plot?

My purpose is to recognize the volatility clustering property without statistical tests such as The Lagrange Multiplier (LM) test.

24 February 2021 4,150 3 View

How to search for crystal structure for material with atomic position labelled?

I am using the crystallographic open database and materials project to search for cif file but the exact structure is not mentioned or how can I deduce that the given structure and atomic position...

23 February 2021 6,723 2 View

How to generate AA6061 alloy or any aluminium alloy crystal in material studio?

I need to carry out molecular dynamics simulation on Aluminium alloy. For this i need the crystal structure that which could be further replicated to form a structure.

22 February 2021 1,410 1 View

Build an orthogonal box in ASE?

Hello, I was wondering the best way to build an orthogonal box filled with a defined crystal structure in ASE. I know it could be easily done in LAMMPS, but I guess it is also doable in ASE. The...

21 February 2021 5,899 4 View

How to overcome convergence issues in concrete arch models?

Hi, I have modelled a three-span arch bridge with soil fill over along with pedestals. The FE modelling is done in LUSAS with HX8M solid elements (i.e. 3D solid modelling). The non-linearity is...

20 February 2021 1,346 2 View

How can I make sure that BCTC doesn't fall out of solution/form DMSO crystals when treating cells?

I resuspended my BCTC as described on the bottle at 10mg/mL in DMSO. However, I can see the formation of crystals which I can only assume are DMSO and that the drug is precipitating out of...

14 February 2021 5,633 1 View

Is there a way to tell based on appearance which protein crystal should diffract the best?

I have had unheard of success with protein crystallography lately from a super successful protein expression and purification batch. I have attained a lately reproducible vast amount of crystals...

09 February 2021 5,155 5 View

What constraint can be used for rigid steel saddles and conrete beam under four point loading in ABAQUS?

Nodes are missing intersection with their respective master surface or outside the adjust zone, when using tie constraint.

01 February 2021 3,591 6 View