What is the difference between Montmorillonite and Montmorillonite K10 ? which is to be used in evaluating oil recovery ?

More Rohit Kumar Saw's questions See All

What are different ways to check for calibration and laser problem in DLS-zeta machine?

while measuring the zeta potential of sample, results are not consistent showing a high standard deviation for each measurement. For HPLC water it is showing a negative value of 2 mV with standard...

08 September 2019 2,170 3 View

How to determine the mineralogy of sandstone by XRD ?

How to determine the mineralogy of sandstone by XRD ? such as quartz wt% ,kaolinite wt% etc. by XRD data...

11 December 2018 7,044 0 View

Can Interfacial rheology between crude oil and brine be measured with cup and bob type rheometer?

i am looking to measure the elastic modulus and viscous modulus of oil and brine interface.

04 May 2018 9,597 2 View

How the wettability of rock sample can be changed by ageing in pure hydrocarbon oils only?

I want to do wettability analysis of hydrocarbon oil (octane)/rock/surfactant solution system. but to do the analysis first I have to make rock surface oil-wet. Since hydrocarbon oil does not have...

27 February 2021 5,383 3 View

Gas sensor response and recovery time independant of flow rate and chamber volume?

I am trying to obtain the response and recovery times for my gas sensor device. It appears the the response/recovery times are primarily dependant on the flow rate of the gas I inject into the...

26 February 2021 1,511 3 View

What is the suitable range of Sulfur content and Viscosity of Heavy fluid Oil that used in Kiln?

What is the disadvantages of high sulfur content to the ceramic burning process? and what is the effect of outranged viscosity?

24 February 2021 8,219 2 View

How can Gamma Ray API units be converted to CPS (counts per second)?

Oil and gas companies run gamma ray tool and take readings in API units while Gamma ray is also noted in cps, so how these units can be converted into each other?

24 February 2021 7,545 2 View

How to remove compound ( Europium complex ) from paraffin oil?

How can I remove my compound from paraffin oil? Mistakenly my compound fell in an oil. Compound = Europium complex

22 February 2021 5,667 2 View

When I mix oil and NaOH solution, Why solid layer in the surface is formed?

During my trial for lubricant oil re-refinery process, I use NaOH as coagulant agent. After overnight of gravity settling, a solid layer in the surface was form. what product is that? since the...

22 February 2021 2,116 4 View

The type of filter paper used to filter an epoxidized oil (the mixture is an epoxidized oil with magnesium sulfate) ?

I have a mixture of epoxidized oil and magnesium sulfate wich type of filtre paper should i use

21 February 2021 3,944 3 View

What reaction will occur when adding hexamine into ammonium nitrate in an acidic medium?

Hello, I am investigating properties of water in oil emulsion explosives. And adding hexamine (hexamethylenetetramine) into one of the phases that are used to make the emulsion should increase the...

21 February 2021 8,680 1 View

How can we study the adsorption efficiency of microgel at the oil-water interface?

I am studing the mircogel at oil-water interface. I want to know the adsorb amount of microgel at the oil water interface. How we can determine this amount?. I will highly appreciate your...

19 February 2021 2,787 1 View

Does anyone know, can i do cryosectioning of whole aorta after oil red O staining and use the cryosection parts for further analysis?

I would like to quantify the lesions on aorta. I want to take image of atherosclerotic plaques formation in aorta by using O red Oil Solution. After the staining, what will be the storage...

16 February 2021 5,876 2 View