What Is the Correct suction Pressure and discharge pressure for domestic refrigerators Using R134a in bars/psi?

More Muhammad Ahsan's questions See All

How can I control/vary Evaporator and condenser pressure for a domestic refrigeration system using Variable speed compressor?

I'm supposed to conduct experimentation on domestic refrigeration system so I've to vary these Evaporator and condenser pressure as variable parameter. Therefor i want to ask how to do that. Your...

31 December 2018 10,023 4 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

How to grow E.coli on the low salt LB agar plate with 50 or 100ug/ml of Blasticidin?

Hello, I would like to ask how to grow E.coli which resists 50 or 100ug/ml of Blasticidin. I have tried many methods by using low salt Luria-Bertain(LB) agar plate. However, no colonies grow. Let...

01 March 2021 2,027 2 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Timeout error!! Processor in the loop (PIL) using STM32F4 Matlab 2018a?

Dear Researchers I am trying to perform a PIL simulation using STM32F4 Discovery board and comunication serial USB TO TTL. During simulation I receive the following timeout error: An error...

01 March 2021 2,327 1 View

Mohammad Vajdi Popular answer

Ive asked an expert about this to help you. He said that they charge the system with R134a so much that the all evap. coils have condensed vapor on them. He said they dont pay attention to pressure, since they can not install pressure gauges for all Ref. systems.

Mohammad Vajdi

Muhammad Ahsan

Thanks very much for helping.