What is the most reliable source to get Impact factor of journals?

Source to get Impact factor of journals

01 March 2021 6,654 2 View

Is anyone familiar with the cyclic compressive fatigue testing (BS EN 12697 - 25) ?

I would like to get more information on the cyclic compressive fatigue testing (BS EN 12697 - 25) which is typically done for bituminous material in pavement design. Any one can advise on the...

28 February 2021 2,004 3 View

Why initial concentration of Pb not the same as calculated one when testing using AAS?

I am currently doing research on the adsorption of heavy metal using magnetic reduce graphene oxide. I use AAS to determine the concentration of the heavy metal. I prepare the Pb solution with...

26 February 2021 9,580 4 View

Stress/strain tensors decomposition ???

25 February 2021 6,760 1 View

Best FE Program for Concrete Strengthened with FRP Sheets?

Colleagues, I have been using ANSYS to model concrete strengthened FRP sheets, but less than happy with it. Any has recommendation for efficient, easy to use FE program for modelling concrete...

22 February 2021 7,528 3 View

Any information about dinitrosalisylic acid reagent end point color stability ?

I work on estimation of alpha amylase activity using dinitrosalisylic acid reagent If i put the reagent to stope the enzymatic reaction and allow the reagent to react with the produced reducing...

17 February 2021 7,402 4 View

Using liquids as superstrate in Fabry-Perot Cavity Antenna?

Hi, A Fabry Perot Cavity allows to increase the directivity of a low gain antenna by putting in the top of cavity a superstrate with high permittivity such as a ceramic (er=10.2). However,...

09 February 2021 6,799 8 View

Experiment statistical analysis?

07 February 2021 3,635 3 View

Distribution of modes fields ?

Hi, We find a specific distribution of electric fields in structure for different frequencies which can be seen using em solvers and known as modes. I would like to know how we can choose the...

04 February 2021 10,043 3 View

Greetings Doctors, If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers?

If i did a same experiment for a 2 populations and i need to publish this work in a 2 different papers can i use the same word in the writing of these 2 papers or this would considered as...

04 February 2021 4,648 4 View

Precipitate after adding laemmli buffer to protein solution containing Potassium Acetate?

Hi, I am running a size exclusion chromatography experiment with a buffer containing Potassium Acetate as a salt. I analyse these fractions through SDS-PAGE. After boiling my SEC fractions in...

01 March 2021 2,622 3 View

Benefits of the 24 welled plate?

We have always used the 96 welled plate, the 48 welled plate but apparently there is much evidence on the 24 welled plate and above all its benefits.It states it is the same you would use on ELISA...

28 February 2021 1,149 1 View

Can two EC50 values with different hill slopes be compared?

Hello, I fit a classical dose response curve Y=Bottom + (Top-Bottom)/(1+10^((LogEC-X)*HillSlope)) to my data (not related to inhibitors etc). The model I use is purely qualitative but it fits...

23 February 2021 8,155 5 View

Will SARS-CoV-2 Spike be broken into S1 and S2 by denaturing conditions?

Hello, I am performing a western blot of my SARS-CoV-2 Spike-pseudotyped lentiviral particles. I denature my virus by adding concentrated virus to 2X Laemmli buffer at 1:1, then boiling for...

17 February 2021 4,844 4 View

Measuring Total immunoglobulin whole-body of fish larvae?

Hi Dear All, I prepared the extract of fish larvae whole body with PBS. Then protein concentration of the whole-body extraction samples determined by the Folin-Ceiocalteu-Phenol method (Lowry...

17 February 2021 1,971 3 View

What is the best temperature to coat an ELISA plate?

Hello, I want to control the temperature of my ELISA plate during incubations to get consistent results. In general, what is the best temperature to coat the plate with antibody? I have been...

16 February 2021 2,377 7 View

How to visualize stress in a coating defined by "Skin" in Abaqus?

Hello All! I'm trying to model a contact between a coated substrate and a tip in Abaqus. The coating is ultra-thin compared to the geometry of the substrate. So I defined the coating using the...

16 February 2021 1,594 3 View

Should the AUC in a concentration-time graph of a subcutaneous implant be roughly the same for poeple?

I have 2 concentration time curves of a subcut drug implant. the first group has a peak around the 50 day mark where as the second group does not. Both groups received the same implant by the same...

10 February 2021 2,305 3 View

Is there a way to tell based on appearance which protein crystal should diffract the best?

I have had unheard of success with protein crystallography lately from a super successful protein expression and purification batch. I have attained a lately reproducible vast amount of crystals...

09 February 2021 5,155 5 View

What is the best analytical software for XRD data?

How can I determine any phase from the powder XRD data and how can I determine the morphous or amorphous state of the sample from XRD data?

09 February 2021 7,867 5 View