What is the best type of compressor (discharge: 6-8 bar) suitabel for Syngas which is under 1 atm?

More Anand Patel's questions See All

What will be the pressure in the pipe which connects gas input (under 1 atm) and a comressor which compresses the gas at 6-8 bar ?

A compressor is compressing a gas which is at under 1 atm and delivers it to a higher pressure. (i.e. 6-8 bar). I am interested in the pressure in the pipe beofre compression.

05 June 2019 2,923 2 View

What is the best way to remove Tar and Water Vapour from Syngas?

I want to use Syngas coming out of the gasifier in a gas engine. Therefore Tar and Water vapour must be removed as much as possible. Syngas temp. is 450 C and Pressure is 1 atm. Please, answer...

03 April 2019 671 5 View

In case a flame of a natural gas, Why emissivity strongly depends on temperature?

What is the fundamental equations to calculate the heat transfer in this case?

10 November 2018 2,772 0 View

How will the temperature profile (depending on time) of a stone wall heated through fire from one side look like?

Which are the fundamental equations to calculate the temperature profile?

10 November 2018 2,836 0 View

Why depends convective heat transfer above a long plate on the length of the plate? While length of the tube has small influence ?

Length of a tube has a very small influence on the internal heat transfer while convective heat transfer in long plate depends on length of the plate? Why? any scientific reason?

07 August 2018 1,888 7 View

How can we determine the heat transfer cofficients of two fluids in concurrent flow heat exchager?

Whot do heat transfer cofficients depend on? What are the equations for calculating heat transfer area and heat transfer flow in such heat exchanger?

07 August 2018 3,965 10 View

Does the pressure(-600 mmHg) affects pH?

When I conducted the degassing experiment using decompression under anaerobic condition(and I used ferrous based chelating agent), the oxidized ferric were observerd. So, could you tell me the...

03 March 2021 4,892 5 View

Why can't make aluminum nitride film successfully by use sputter?

We use reactive sputtering process to make aluminum nitride film, and want to make c-axis aluminum nitride film on a silicon substrate, but the crystal orientation cannot be seen with...

03 March 2021 7,975 3 View

Is there any test to determine the cardiovascular risk of patients with obesity? from the perspective of obesity?

We found tests to determine cardiovascular risk taking into account lipid profile, blood pressure, age, history of diabetes, other laboratories. But when weight is involved, there is a paradox. I...

02 March 2021 6,036 1 View

Why are the velocities so high in my Boussinesq approximation Fluent simulation?

Hello, I have a mechanism where air rises due to convective flows. In this simulation, nothing is driving the air except this. I understand that the Boussinesq approximation only works for small...

02 March 2021 4,910 3 View

What is the characteristic length to determine the Reynolds number for the scattered turbulent fluid flow?

Dear all, I just saw this example in FB on the difference between laminar flow and turbulent flow. The flow from a pipe hits the sink and scattered. The flow from the pipe is characterized as...

02 March 2021 1,999 5 View

Why almost every element would be metallized in sufficiently high pressure and low temperature?

(This statement is from wikipedia, BTW). What is so special about metallic bond that is limiting high-P low-T state of a matter (as long as individual atoms exist, not white dwarf of neutron star...

02 March 2021 3,309 2 View

Sutter electrode holder leaking after applying positive pressure. How to fix?

I am using a Sutter electrode holder for my patch clamp experiments, but I'm having trouble keeping positive pressure inside my electrode due to a leak out of the back of the holder. I have added...

02 March 2021 5,829 1 View

What SPSS analysis should I run with one IV (with two levels) and two DVs?

Hi, I am trying to figure out which test would be most appropriate to run for the following question: Is there a difference in task blood pressure between smokers and non-smokers? There are two...

01 March 2021 8,235 2 View

How much pressure we can reduce at the outlet to avoid Reverse Flow?

I am simulating Heat Exchanger. I have tried and tested all the methods to resolve this issue from the internet like refining mesh, improving skewness and orthogonal quality ,extending outlet to...

01 March 2021 6,985 3 View

Issues with Permeabilization during Flow Cytometry?

Hello Everyone. Currently I am working to characterize macrophages in the myocardium after ischemia-reperfusion injury in rats. Due to the low total cell number isolated from rat hearts I can...

01 March 2021 3,867 3 View

Abdulrahman Alodan

How much is the flowrate through the compressor?

Anand Patel

Abdulrahman Alodan Its same. 1.5 m3/s

Ritesh Sojitra

Dear Anand, to answer your question volumetric flow rate, and appx molecular weight will be required. In addition to that service type required i.e. continuous or intermittent.