In case a flame of a natural gas, Why emissivity strongly depends on temperature?

11 November 2018 0 3K Report

What is the fundamental equations to calculate the heat transfer in this case?

Badges
Science topic

More Anand Patel's questions See All

What is the best type of compressor (discharge: 6-8 bar) suitabel for Syngas which is under 1 atm?

Syngas is produced in a reactor at 1 atm. Then it is passed through a condenser where a pressure drops becuase of friction so goes under 1 atm. It need to be compressed afterwards upto 6-8 bar and...

05 June 2019 9,695 3 View

What will be the pressure in the pipe which connects gas input (under 1 atm) and a comressor which compresses the gas at 6-8 bar ?

A compressor is compressing a gas which is at under 1 atm and delivers it to a higher pressure. (i.e. 6-8 bar). I am interested in the pressure in the pipe beofre compression.

05 June 2019 2,923 2 View

What is the best way to remove Tar and Water Vapour from Syngas?

I want to use Syngas coming out of the gasifier in a gas engine. Therefore Tar and Water vapour must be removed as much as possible. Syngas temp. is 450 C and Pressure is 1 atm. Please, answer...

03 April 2019 671 5 View

How will the temperature profile (depending on time) of a stone wall heated through fire from one side look like?

Which are the fundamental equations to calculate the temperature profile?

10 November 2018 2,836 0 View

Why depends convective heat transfer above a long plate on the length of the plate? While length of the tube has small influence ?

Length of a tube has a very small influence on the internal heat transfer while convective heat transfer in long plate depends on length of the plate? Why? any scientific reason?

07 August 2018 1,888 7 View

How can we determine the heat transfer cofficients of two fluids in concurrent flow heat exchager?

Whot do heat transfer cofficients depend on? What are the equations for calculating heat transfer area and heat transfer flow in such heat exchanger?

07 August 2018 3,965 10 View

Resistor definition in Piezoelectric bimorph with ANSYS workbench

Hello, good day! I am trying to simulate similar bimorph piezoelectric harvester with below commands. However, the output power doesn't change with resistor value. Please help to find the reason. ET,10,CIRCU94,0 !SET UP RESISTOR R,1,100000 !RESISTANCE VALUE TYPE,10 !SET ELEMENT TYPE E,1,2 !CREATE RESISTOR BETWEEN NODES 1 AND 2 Thanks in advance Regards,

02 March 2021 0 0 View

Is There Any Feasible Method To Test Fluorescent Compounds Other Than Fluorescence Spectrometers ??

Is There Any Feasible Method To Test The Efficiency Of Fluorescent Compounds Other Than UV Spectrometers ? Suggestions Would Be Appreciated !

02 March 2021 5,785 3 View

Where can I find life cycle inventory or assessment of non woven materials?

Dear network, I am looking for the LCA or LCI or at least the energy balances of the non woven fabrics process for my master project, in specific for natural fibers, yet I have found...

02 March 2021 9,662 1 View

What are the countries most affected by extreme rainfall as a result of climate change?

Increased heat, drought and insect outbreaks, all associated to climate change, have increased wildfires. Decreasing water supplies, declined agricultural yields, health impacts in cities owing to...

01 March 2021 7,168 9 View

What is recommended for solid domain in ANSYS FLUENT?

Should I mesh the solid domain ? or should I use wall thickness? or Shell conduction? for Heat Transfer between two fluids of a Heat Exchanger. what is recommended?

01 March 2021 9,785 3 View

Heat exchanger with liquid Nitrogen as coolant?

I want to cool Natural Gas from 195 Kelvin to 138 Klevin in a heat exchanger by using liquid nitrogen as the coolant medium. When entering the heat exchanger, the liquid nitrogen will have a...

01 March 2021 6,450 5 View

Any research papers for extraction of nutrient deprivation on macroalgae? Analysed by HPLC-UV and GC/MS. Possibly from macroalgae genus Rhizoclonium?

I am doing my thesis on the nutrient deprivation on the macroalgae Rhizoclonium sp. I will be analysing the levels over a period of roughly 5 days by HPLC-UV and GC/MS. I will be using seawater as...

28 February 2021 6,477 1 View

How can i resolve the "final solutuin is not converged" error in Comsol for my heat transfer simulation??

I have been trying to simulate heat transfer problem in Comsol 5.5 for long time but it always throw an error stating: "Failed to find a solution. Maximum number of Newton iterations...

28 February 2021 8,626 3 View

PUC19 as a transfer plasmid for lentiviral delivery?

Hello, Is it possible to use pUC19 as a transfer vector to be packed in using the second generation viral particles packaging system( pMD2.G; psPAX2 plasmids)? As far as I understand it there is...

28 February 2021 4,868 2 View

Necessary tube lenght to cool Natural gas in a dry-ice cooling bath?

I have a tank which contains natural gas at 250 Bar and 293 Kelvin. I want to cool the gas in a dry-ice cooling bath to about 195 Kelvin. The gas will flow in a copper-tube through the bath with a...

27 February 2021 8,128 1 View